Activity in Technology and Support
Cisco Archive config - any changes / Cisco commands
Hello Professionals,I have configured Archive to log config whenever type write memory.I would like to use this auto backup in other way too.Could anyone tell me how to configure followings?1. Is there possible to backup config whenever I make any ch...
Problem with SNTC account in Collector
Hello, when we try to access to "Software Updates -> Server connection setup" and we put the credentials that page freezes and does nothing.Also, the upload of files fails.We just updated to the version 2.11.Regards.
Resolved! No answer ring issue
CUCM 12.5, I have a Line Group with 3 users, top down then hunt pilot to VM. The RNA Reversion Timeout is set to 15 (per Cisco). One of my users (the first in the line group) sent me a message saying that incoming calls ring to her phone about 10 t...
Forward traffic from subnet to another on C3750
hi guys thanks for your suggestions in advancei just reconsidered my whole message. after trying some things. i think i need to set up acl but i'm far from good at it.what would be the ip access-list extended or access-list lines that'd allow me to h...
1921 Router Config Help
Hello, I know very little about configuring cisco hardware and need some help..... we are currently running an 1800 router and I obtained a new to me 1921 router and would like to replace the 1800 router with the newer one, I managed to get it factor...
No Privilege to download AnyConnect Secure Mobility Client for Contest
This is for the Cisco Modeling Labs CCNA Topology Contest the link to download a secure client or AnyConnect client in the instructions needs licensing.https://developer.cisco.com/docs/sandbox/getting-started/#sandbox-vpn-info
SNTC APIs
Trying to figure out what I have missed. I have SNTC API developer access in the SNTC portal, but the APIs don't appear in the API console (apiconsole.cisco.com). Anyone seen this before?
ISR 4k Netflow not sending data
I've got 15+ Cisco ISR 4000's (a mix of 4331s and 4551s) in our network and when trying to setup Netflow to PRTG, It seems that when I hit 5 interfaces that need to be monitored, there is always 1 that won't come up in PRTG and that doesn't send data...
CDP Mismatch from CDP: Why?
Switch A, Cisco 9300, VTP mode transparentinterface GigabitEthernet1/0/5switchport access vlan 3switchport mode accessSwitch B, Cisco 3560, VTP mode transparentinterface GigabitEthernet1/0/1switchport access vlan 3switchport mode accessVlan 3 (L2) vl...
WIFI design for the warehouse
Hello everyone. Much has been written and said about the design of WIFI for warehouses.I would love to hear from your experience in order to make a decision on a complete system from MERAKI16 corridors each about 60 meters long. shelf's between each ...
Multiple sub interfaces with Native vlan's?
Sorry, I am reposting because I want the community to see this because where I previously posted, the thread shows resolved already.I have an ASR 10g interface that is connected to a native vlan1 in a HP switching fabric (8 switches) for databases (i...
FTD's - Firepower dropping HTTPS traffic using TLS 1.3 Hybridized Kybe
HelloWe have a lot of clients getting the following error when contacting diffrent sites: ERR_SSL_PROTOCOL_ERROR, we have read that SonicWall and Palo Alto also have these problemes. Solution is to turn off "TLS 1.3 Hybridized Kyber Support" in chro...
vSmart Login Banner not coming before login promt on version 20.9.4
Hello Guys,Good Day !!This is very strange that : on version 20.9.4 the login banner is coming after the login prompt but it is perfectly coming on version 19.2.31 i.e. before login prompt.Would you please help me to fix : i am on version 20.9.4Early...
upgrade process of firepower 2130
hello We have a old fire power that I have no idea how to upgrade. The actual device is a Cisco Firepower 2130 Threat Defense (77) Version 7.0.4 . Cisco Adaptive Security Appliance Software Version 9.16(3)18. and we have a FMC that is Cisco Firepower...
Minor edit in one of the OpenTelemetry Blog
Hey!I'm Chitransh, part of the team at SigNoz.Thanks for using SigNoz as one of the Observability backend for OpenTelemetry in this blog - https://www.thousandeyes.com/blog/data-observability-backend-opentelemetryI just wanted to point out a small c...
| User | Helpful Count |
|---|---|
| 115 | |
| 112 | |
| 85 | |
| 64 | |
| 59 |
