FindIT Network Management Discussions
Join the FindIT Network Management discussion community and gain valuable insights from industry exp...
63 PostsActivity in Small Business Support Community
FTD intervlan questioning,
Scenario,Host-A(10.10.30.3/24) connects to access port on SwitchA with various other vlans also configured via access ports. SwitchA connects on a Trunk port to a CatSwitch. Firepower inside ½ interface trunks to CatSwitch. On The CatSwitch 3 vlans; ...
Cisco 881 router.
I have a new laptop, and have lost the ability to gain remote access to my private server.
Firmware update
HI,i am trying to update my SG500 and SG 300 series switch to latest firmware. currently running in 1.3.0.62 and planning to upgrade to 1.4.11.5. i have downloaded the firmware from cisco portal sx500_fw-14115.ros. while performing i am getting an be...
VLAN configuration RV042G & CBS220
HelloI'm trying to set up VLAN's but can't get it working.I have these components- firewall Cisco RV042G- Switch Cisco CBS220What I would like to create is three separate VLAN's with192.168.1.1 (my default LAN)vlan-2 192.168.2.1..vlan-3 192.168.3.1....
CBD 2.7.1 Error while using a wildcard certificate
I'm running CBD2.7.1 and installed a public wildcard certificate.The following error is flashing on the top of the dashboard:"Server certificate does not contain your server address in Subject Alternative Name."Is this a bug when using wildcard certs...
Retrieve Serial Number Info for Cisco WAP4410N Access Point
Hi,I have tried to retrieve serial number info for 3 units of the Cisco WAP4410N Access Point devices via Web GUI and CLI, but it seems can't find the serial number info for this model. Kindly advise further, thanks.Regards,Wilson Leong
Software Patching and Updates
Hi all,The license of Cisco Switch has lapsed. Would it still eligible to obtain software updates and subsequent patching? As my current Cisco Switch did not renew the license while looking the trend of new vulnerabilities arising from time to time. ...
initializing network
hello, we have a cisco spa504g at my work place connected through Telstra. it has been saying 'initializing network' for 2 days now and the microphone button is red. we have tried resetting/restarting in each and every way but no changes. also the ph...
Need help with Cisco SPA 112.
I have recently bought a SPA 112, and arrived yesterday, I was able to get into config settings, i factory reset it, its the same ip but when i look it up its not working. I need help with this, and I Think it might be company locked. I really need h...
Switch power shuts down on it's own
We have a Cisco Switch 350 that just powers down on its own. The logs do not show anything as it is a limited log and cleared when it powers off. It happens often and it's not a power outage or power brownout. The switch is also on a good UPS and we ...
How can I delete a fixed profile rule in a Linksys ATA?
I have a Linksys SPA2100 ATA that I used with a previous VoIP provider. I did a factory reset but their profile rule is still listed in the first Profile Rule section under the Provisioning tab. Profile Rule B, C and D are blank and I can enter a pro...
SPA2102 Line 1 "Not Registered"
The SPA2102 is running firmware 5.2.5. Line 2 works fine. If I set up line 2 incorrectly, I get "failed" as expected. Line 1 is another story. No matter how I set up line 1, the status remains "Not Registered". It would seem that the line is not enab...
cisco room meeting navigator panel didnot take network
Hi,when i connected cisco navigator panel to codec kit plus it shows 'has not yet received DNS address from DHCP' and i tried to connect with wifi but the wifi doesnot work because i disconnected the ethernet from codec and check with navigator panel...
Resolved! Remote access to voicemail box UC320W
Is there a way to access your messages from outside the office? I have tried *, # and looked at our options but do not see anything refering to outside access.
SG500 not saving config after removing VLAN tags from ports
Hey there, We use some SG500s here and I can't get them to work with our VLANs. We have some ports on our switch that are tagged with VLANs, but whenever I untag them using the GUI, I can see the changes being made when I telnet into the switch. I th...
| User | Helpful Count |
|---|---|
| 3 | |
| 3 | |
| 2 | |
| 2 | |
| 2 |
