Cisco Catalyst Center
This community is for technical, feature, configuration and deployment questions. For production dep...
2155 PostsActivity in Networking
vSmart Login Banner not coming before login promt on version 20.9.4
Hello Guys,Good Day !!This is very strange that : on version 20.9.4 the login banner is coming after the login prompt but it is perfectly coming on version 19.2.31 i.e. before login prompt.Would you please help me to fix : i am on version 20.9.4Early...
Please help us investigate Service "ipfib" (PID 12792)
We found N7K-C7010 line card module 3 reload and found logging as below. 2024 Apr 26 13:08:19 SNIPER-01 %SYSMGR-SLOT3-2-SERVICE_CRASHED: Service "nfp" (PID 1130) hasn't caught signal 11 (core will be saved).2024 Apr 26 13:08:20 SNIPER-01 %NFP-SLOT3...
DNA Center and NetFlow
Hello, Is it possible to use DNA Assurance to know Top N application/Ports/End points consuming the traffic ?
NTP and Syslog packets with specific IP Address
Hi All,I have a couple of C9300 L3 switches that are connecting to an ASA firewall. The NTP and the syslog server for the switches are located behind a firewall.When one of the switches request/send packets the gateway IP is the source address on the...
After changing PPPOE max session , IPTV not connecting automatically A
Team,On this Te0/0/0.667 subinterface we have more than 200 users. so we set the PPPOE maximum session.After setting up PPPOE maximum session to 1000 , IPTV not connecting automatically and getting option SKIP or RETRY. after select skip IPTV getting...
copy xmodem initializing no transfer c2960
Hi Guys, i had this problem for 8 hours now and can't seem to get it cracked... after i input the command copy xmodem: flash:c2960-lanbasek9-mz.152-7.e9.binand using the SecureCRT going to Transfer > send xmodem I get this and after that nothing happ...
Cisco ISR not getting DHCP / IP Address
My router not getting IP Address after reload. Interface IP-Address OK? Method Status ProtocolGigabitEthernet0/0/0 192.168.231.9 YES NVRAM up up---GigabitEthernet0/0/1 unassigned YES DHCP up up--- Gig 0/0/1 Connected to ISP Router, since we not gett...
Is there a standard for making SVI and VLANs on WLC9800?
What is the criteria to create SVI and VLANs in the 9800. If you take multiple AP management bands (vlan) to the same network Do I have to need several SVI and/or Vlans?
Multiple sub interfaces with Native vlan's?
Sorry, I am reposting because I want the community to see this because where I previously posted, the thread shows resolved already.I have an ASR 10g interface that is connected to a native vlan1 in a HP switching fabric (8 switches) for databases (i...
Resolved! Cannot see application health in DNAC
Hi,We are trying to get application health to be seen in DNAC. We currently see only usage and throughput, it's missing other parameters to calculate it.Considering our employees are mostly using wifi it would make sense to configure netflow on WLC. ...
DNA Center Full Backup Size
Hi, I have a DNAC Server gen 2, configuration with 2 SDA Fabric Site. I managed about 215 Devices (included Fusion Router, Border Switch, Intermediary Switch, Edge Switch, WLC and AP). I doing a full backup but size is so big (~ 213 GB), backup progr...
Cisco 2960S not pinging, but has DHCP address
Hi,I am trying to set up an SSH connection to my switch, but right now there is some lower level problem. I have set up my FastEthernet0 interface to ip address dhcp and the command show interfaces FastEthernet0 shows the correct address. Even if I t...
BOOT FAIL C cisco catalyst 9300
When I start the switch, the text BOOT FAIL C appears in the console and the gear indicator, the system, flashes orange, tell me what to do?
Resolved! L2TPv3 tunnel between Cisco 2901's
We're trying to form an encrypted IPsec/L2TPv3 tunnel between two 2901 routers running IOS 15.4+. When we try to connect, we can see that the IPsec tunnel is up and that the xconnect session is up but no L2 traffic is traversing the tunnel. We are ...
Resolved! Removing Device Pack file from Prime Infrastructure
Hello.On the Software Update page of Prime there is one Pack which i can not install or delete because it is already included in another installation i did before. Now this pack stays on the page and i am not able to remove it. Does anybody know wher...
| User | Helpful Count |
|---|---|
| 71 | |
| 40 | |
| 39 | |
| 35 | |
| 34 |
| User | Count |
|---|---|
| 23 | |
| 17 | |
| 16 | |
| 11 | |
| 10 |
