Apr 16 04:14:35.390: %SW_MATM-4-MACFLAP_NOTIF: Host 001b.0907.fe0e in vlan 11 is flapping between port Gi1/1/1 and port Gi1/1/2Apr 16 04:14:35.390: %SW_MATM-4-MACFLAP_NOTIF: Host 001b.0907.fe0e in vlan 11 is flapping between port Gi1/1/1 and port Gi1...
Hi all!English is not my first language, so I am sorry in advance if my words confused you. I tried my best.As far as I know, CEs don't have vrf in general, so CEs would use ipv4&ipv6 address family of BGP to form BGP neighbor with PEs and advertise...
I wanted to test a local account on a Nexus switch and bypass the radius (ssh)connection. To do so, I add the aaa authentication login default local I am now able to access the local account but I wanna get back to the previous configuration. When...
When go to device 360 for an AP and click the Intelligent Capture buttom, there is no data there. And there is a warning icon "gRPC link is not ready (shutdown)". From the WLC gui (Monitor - Intelligent Capture) I can see that the state is active.
Hello,As per the below diagram I have two switches S1 & S2. Hosts H1 & H2 are connected to the switches and are in different vlan but same subnet. So, by default they will not communicate as they are in two different broadcast domain.To make them com...
hello. I understand that Connected routing has an AD value of 0. The IP bands on the 1st and 2nd floors are different. 1st floor: 1.1.1.0/242nd floor: 2.2.2.0/24 There are two firewalls on top of the backbone. The band will be 3.3.3.0/24. If you conf...
Dear all,I have a reoccurring issue, where commands I manually remove from SDA devices keep showing up.I want to disable "snmp-trap enable traps syslog" on the devices. The first time I tried to do this via applying a template through network profile...
Sur un Nexus9000( NXOS 9.3(9)) j'ai paramétré aaa authentication login default local afin de bypasser l'authentification par défaut par le radius(ssh). L'action fonctionne très bien, mais lorsque je veux revenir á la config initialle en supprimant la...
Hello,Our Wireless Team has reported their inability to see wireless clients connected to / associated with the Wireless APs monitored in DNAC (Please see attachment). The Wireless Controllers are 9800s and 8540s. We have them discovered and monitore...
I have two 9410 switches connected in stackwise , when entering "show version" i can only see the primary stackwise member uptime. How can i see the uptime for the second member?
Greetings,I'm checking the "show bgp x.x.x.x" output in 3 different XR routers A, B & C in an ISP environment.Here's an example as the best path part of the output:Path #1: Received by speaker 0 Advertised IPv4 Unicast paths to peers (in unique updat...
Hello,I have a switch I am unable get a prompt on the console port.I can SSH to it, and have confirmed that the baud rate and stop bits are correct from the console switch. There are two other switches that I can console to.The differences are that t...
Greetings!So I was practicing to configure VTP and VLANs. For a start, I created 3 switches (only 2 being turned on). The trunks are working fine as the switches are able to acquire an IP addresses via dhcp from a dedicated router and vtp appears to ...
Hi anyone can assist me on the VPC configuration ? The status not up. VPC Status : switch(config)# show vpcLegend:(*) - local vPC is down, forwarding via vPC peer-link vPC domain id : 700Peer status : peer link is downvPC keep-alive status : Suspende...
I am working with ISR 4331 in Packet Tracer 7.3.0. Although the router has 3 Gigabit interfaces, which I can configure and switch on, Packet Tracer only allows connecting 2 interfaces (using the connections button). Is this a bug of Packet Tracer? Is...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: