Data Center and Cloud

Cisco ACI - ELAM capture

Hi All,I am geting below alert while configuring ELAM on ACI leaf switch.Can any one suggest on this.module-1# debug platform internal tah elam asic 0Invalid CLI for platform type - TAHalso can some one share the procedure to perform the ELAM capture...

Nexus 9332C Booting ACI image from boot loader issue

Hi Guys, I am looking for some help as I hit obstacles and I think that I have tried all possible options, to get this issue resolved.So I was converting Nexus 9332C from NX-OS mode to ACI mode to version aci-n9000-dk9.14.2.6o.bin and at some point p...

Cisco Fabric Interconnect is showing six(6) Pmon Services as failed

Cisco Fabric Interconnect is having some Pmon Services as failed ================================================== FI-B(local-mgmt)# show pmon state SERVICE NAME STATE RETRY(MAX) EXITCODE SIGNAL CORE------------ ----- ---------- -------- ------ ----...

Cisco Hyperflex cluster installation failed

Hi All, My hyperflex cluster failed with the error "configure Service profile(SP) failed" "Associating Service Profile" during the UCSM configuration in each server but validation was successful. I have 6 nos of hyperflex UCS 240 m5 all-flash nodes a...

MACSec not supported on N7K-F312FQ-25?

Hi All,Can any one confirm that on a N7K-F312FQ-25 SUB2E is IEEE 802.1AE MACsec not supported?thanks with any pointers.with kind regardspiotr

BD Subnet advertised over L3out

Hello when a BD subnet is advertised over an OSPF L3out, i'm seeing tha subnet as E2 external route with metric 20 on the router connectd to BL (VPC link). Why the subnet is shown as external and not internal OSPF route? Why the metric is 20 ? Regard...

Issue with Assigning a Provided Contract to vzANY in Cisco ACI

Hello everyone,I'm reaching out to the Cisco community for assistance with a problem I'm encountering regarding the assignment of a Provided Contract to vzANY in Cisco ACI. I've tried various solutions but so far haven't been able to resolve this iss...

ACI multipod with vPC HA FW

Hi All, I need your assistance to check if the following configuration going to work and are there any drawbacks/caveats?So far I identified OSPF convergence time and impact on a relatively large area 0 *(legacy design). Solution details:I have ACI M...

FI 6248 RMA and UCS-FI-E16UP

Hello I am kwon. FI 6248 has been determined to be RMA and is scheduled for replacement. However, the existing FI is using UCS-FI-E16UP. If I install this with RMA FI, will the 8 port license of UCS-FI-E16UP be activated?

Moquery to check unused EPGs

Hi All,We have 300+ EPGs in our Environment and some of them are not used.Is there a Moquery to list all the unused EPGs?

Cisco ACI - Multi-pod fibre requirements for IPN connectivity

We are currently investigating how we can connect our cisco ACI to IPN for multi-pod connectivity. Currently the we are planning to implement Single Mode Fibre across our datacentres. We would be using catalyst switches for our IPN devices. Our under...

Configure Third Party Certificate for UCS Central

The Cisco Document Team has posted an article. This document describes the best practice to configure a third-party certificate in Cisco Unified Computing System Central Software (UCS Central). Know of something that needs docu...

inter EPG MSO

Hi all, I have a question concerning a use case in our prod network. We need to configure inter-communication EPG between two site via MSO , in this case i have two options : -First is to use a stretched VRF between sites and apply a stretched cont...

F0849 : Configuration failed due to invalid port

Hello,How can I resolve this fault F0849 please? I didn't find the affected object on the GUI!Thank you;

CIMC CLI Command Injection Vulnerability || CVE-2024-20295

We have Cisco Hyperflex nodes model “HX240C-M4SX” in our environment. Could you please let us know if the subjected vulnerability is applicable to this model.If yes, could you please share the fix as well.

Data Center and Cloud

Browse the Community

Share your Expertise