Wireless - Mobility

Connect with peers and Cisco on all aspects of wireless tech including security and network management, LANs and indoor and outdoor access points.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Browse the Community

Activity in Wireless - Mobility

Resolved! Cisco 9124AX as WGB on non-DFS channels

We have this Cisco 9124AX for the European market, configured as WGB (work group bridge) and we would like to use it on non-DFS channels on the 5GHz band.However, we are not allowed to add any such channels to the scan list, we can only use channels ...

C9800-80 in HA cannot install APSP6

Hello everyone,I'm trying to figure out a frustrating issue. Attempting an install of APSP6 keeps bombing out and I'm unsure what steps to take next. Software: Version 17.09.04aROM: 17.3(3r)Error in question:  Dec 13 21:21:01 Eastern: %INSTALL-3-OPER...

C9800-CL please register this device in 58 days alarm

Hello. The following alarm is constantly occurring in the C9800-CL raised to vm. It's like an alarm related to a license, is there a solution? -----------------------------------------------------------------------------------------------------------...

CCC3 by Level 1
  • 84 Views
  • 1 replies
  • 0 Helpful votes

Wired Guest issues in foreign-acnhor setup

Wired guests are not able to get out to internet, they can ping only at when payload is set to 1300 bytes or lower, this seems like an MTU issue, but its only effecting wired guest not wireless guest. Setup is a 9800 foreign on 17.9.5 code and 5520 a...

ammahend by VIP
  • 104 Views
  • 3 replies
  • 0 Helpful votes

AP-AIR2802i-B-K9 No join

l installed newest version of Wireless controller 9800-CL Cloud but wont Join DTLS Error l dont why it wont join to controller 

lisavbedt by Level 1
  • 157 Views
  • 9 replies
  • 0 Helpful votes

Can I change the regulatory domain for our new CW9164I-ROW AP?

We have a 9800-CL Wireless Controller running 17.12.2.  We just got a new CW9164I-ROW AP and its registered by the operational interfaces are down due to a regulatory domain error.  Is there a way to change the regulatory domain for the access point?...

Wireless IOSxe Client Ioslation and multicast

Hey everyone,Questions - on a guest WLAN I have client isolation enabled via the Peer to Peer blocking action to drop.  I can see it blocks peer to peer unicast traffic, however multicast traffic between peers still flows.  I can limit the mdns messa...

Alex-Pr by Level 1
  • 115 Views
  • 2 replies
  • 0 Helpful votes

Resolved! How to disable mac address in 9800 WLC

Hi Guys, As we know, there is option in Cisco 5520 WLC to mannualy disable any Mac addresses of user to deny network access to him. Is there any disable mac address option in Cisco 9800 WLC?

Noovi by Level 1
  • 1605 Views
  • 6 replies
  • 0 Helpful votes

WLC, SSO and OEAP

Hi I got a pair of 5520 in SSO mode version 8.10.190. If you want to run OEAP then you need to enable Enable NAT Address on the management interface. The problem is that the "Enable NAT Address" is greyed out: the question is: is it possible to enab...

nat,.JPG
Moudar by VIP
  • 108 Views
  • 3 replies
  • 0 Helpful votes

Spaces Telemetry issues

I'm trying to get environmental stats back from 9136/9166 on Spaces. I've imported the maps successfully and have enabled the IOT service in spaces. I'm still getting errors for the TDL Telemetry under the troubleshooting section which seems to be pr...

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Top Experts - Last 30 Days