Activity in Technology and Support
Resolved! Cisco Firepower 2130 - no console access
I have a couple of Cisco Firepowers that I can access thru SSH or the FDM, but I can't console to them?-Software version: 7.0.5-72-Configured with primary and secondary-Base license-Not using FMCCan someone tell me how to get console access? Thank yo...
IP routing using domain
The host for my current server (Windows Hyper-V machine with four or five VMs) that handles my email and web sites is going away. I'm planning on moving that physical server to my house and using DDNS to route that traffic in. Realize this is very lo...
Dual ISP connection gi0/2 not able to connect to internet
Hello,I need your help - currently we have a 2921 Cisco router connected to dual ISPs using "gi0/0 & gi0/1" and we are able to connect to either ISP successfully. Once we connect gi0/2 to any device the connected switch is not able to access the in...
The operation took longer than expected.
I have just synchronized both Active Directory and Cisco ISE, ISE is using my server (AD) as an NTP server, everything is fine, but now I'm facing an issue "Status Summary: The operation took longer than expected. This may be caused by slow network c...
Supervisor engines configured for redundancy appear as "STANDBY HOT" and "STANDBY COLD" in the output of the show redundancy states command
Core issueRoute Processor Redundancy (RPR) refers to the provision of support for the redundancy feature. In the RPR mode, one of the supervisor engines is active and operational, while the second supervisor engine is in the standby mode. If the acti...
CBS350 Firmware 3.4.0.17 POE on Ports shows Fault - Short Counter High
I have several CBS350 switches running 3.4.0.17.They are showing POE faults on some of the ports.I'll use one switch as an example. It is a CBS350-24FP-4G.The POE Properties show Nominal Power = 370WAllocated Power = 13WAvailable Power = 357WSoftware...
Trunking an ip addressed inside interface on Firepower 2130
My network endpoints use the IP addressed vlans on my core cisco layer three core switch as their gateway addresses. i.e.- vlan 11 endpoint address 192.168.11.3/24 with gateway 192.168.11.1/24 (vlan ip on core) and vlan 12 endpoint address 192.168.12...
Meraki Duo SSO through SAML
I'm tryign to set up Duo SSO for Meraki Client VPN, the knowledgebase seems out of date as it refers to choosing the Applciation Protect page when currently it's meant to use SAML. I have a few items I am not 100% sure where to get1) I think the enti...
Resolved! How to download crashinfo file?
Hey guys,I would like to know about downloading crashinfo file from the flash drive.Pls see below:RSW01#dirDirectory of flash:/ 2 -rwx 5708466 Feb 28 1993 19:57:48 -06:00 c2960-lanbasek9-mz.122-35.SE.bin 3 -rwx 1048 May 16 2008 ...
Cisco ISE integration with SCCM
Hi While Integrating ISE with SCCM 2012 based on below link, i am getting error related to DCOMhttps://community.cisco.com/t5/security-knowledge-base/how-to-integrate-cisco-ise-with-microsoft-sccm-for-patch/ta-p/3725035 Do any one having solution on ...
Recording Jabber - Overlapping Voices
Hello, I'm having this situation:In the call center we have PCs with softphones installed (Jabber) that replicate the traffic to a recorder in another site.Randomly, we are seeing high levels of Jitter in the flow that is replicated to the communicat...
Hide Finesse Gadget Header/title
Hi, I'm trying to hide the "Supervisor Assist Gadget" title for the Finesse 3rd party gadget. In the gadget xml, I removed the title by which I was able to hide the gadget title and the text moved up to where the title is but now I'm getting empty s...
Not powering up KEM (PID: CP-8800-A-KEM)with CP 8851
I bought a new KEM (PID: CP-8800-A-KEM) along with the cisco ip phone CP8851 but unable to power up the KEM. I am using C2951 ISR with IOS 15.6 and Cisco Unified Communications Manager Express (CME) version 11.5. Please note i am using call manager e...
CBS350 Setup guidance
Hello,I have an ISP router/modem, along with assignable public IP addresses for use. Leaving default VLAN1 alone (mgmt), I created VLAN10 (192.168.0.0/24) and VLAN20 (172.16.3.0/24) on the CBS350.ISP router "internal" ip 172.16.2.1/24On CBS350 port G...
AP2702i degrading throughput
Hi community!I posted about some 2702i in autonomous mode, degrading throughput after some time - see post: Autonomous Mode Failing on Aironet 2702i-z-k9 - Cisco CommunityLast days I got a WLC 2504 and other 2702i access points (in controlled - LWAP...
| User | Helpful Count |
|---|---|
| 103 | |
| 101 | |
| 83 | |
| 71 | |
| 59 |
