Activity in Technology and Support
user auth without user cert?
We have a chicken & egg situation where ISE requires a user's login and the presence of a user cert from AD before the user can be permitted to connect to the corporate wifi. But the user needs to connect to wifi to get the cert. One solution i have ...
Updating Radius server
Hi,If Radius server gets updated with the new IP address, will current users remain connected or will they need to reconnect?I am asking for both AireOS and 9800 WLC.
Resolved! NGFW Sizing
Hi,Please I need an advise to determine the right NGFW based on the below requirements:- Each NGFW physical appliance should provide minimum of 240 Gbps Firewall throughput.- Each NGFW physical appliance must support minimum of 850,000 new TCP connec...
Extremely slow and poor overall WiFi quality with C9130AXI
Recently swapped our 3802i APs for all C9130AXI to get the WiFi 6 capability. Have noticed very poor performance overall. Only change has been with the APs, nothing else. The controller remained to be an AIR 3504 and the switch is a Catalyst 3850 UPo...
cisco jabber lock
Dears,i have Cisco jabber and i need to lock it for a meantime or for long time// is there anyway to know which steps can help me to do that from settings?
Cisco SDA Border to Fusion Connectivity
Do all VNs from a SDA border node need to the same fusion device? We would like to take our Corporate traffic and fuse that to our GRT with a Nexus switch. We'd like to take our IOT and Guest VNs and run them through a firewall for policy and inspe...
WLC 5508 licenses
I have a WLC with 11 registered access points I tried to integrate a new equipment, but I see that I already have my 37 licenses in use. Can you guide me and let me know what this is due to?there is a way to release licenses from the WEB portal or...
Cisco Fabric Interconnect is showing six(6) Pmon Services as failed
Cisco Fabric Interconnect is having some Pmon Services as failed ================================================== FI-B(local-mgmt)# show pmon state SERVICE NAME STATE RETRY(MAX) EXITCODE SIGNAL CORE------------ ----- ---------- -------- ------ ----...
Enterprise Agreement Educational Tutorials
The Enterprise Agreement (EA) onboarding process aims to equip customers with essential knowledge for effective asset management. These resources provide comprehensive guidance on EA principles and tools, enabling seamless EA-software management thr...
Cisco UCCX - Controlling Ready/Not Ready on Specific CSQs
Dears, One of our customers has requested a custom gadget inside Finesse where agents who have more than 1 CSQ can choose which one to be ready on; the current state is the agent has to choose to be ready or no ready on all CSQs. Any hints? Thanks in...
Connection problem when changing to AP2800 hidden SSID
Hello everyone,There is a wireless network in use with AP2800 ME.I plan to link one more AP and change the SSID to a hidden SSID.The added AP operates normally and there is no connection problem. The IPs of all AP users connected to the controller AP...
Site-to-site vpn failover causing memory spike in spoke sites
Hi All. I would like to get your thoughts on the following issue i have been facing since implementing Dual ISP and failover for site-to-site vpn tunnels.Hub Site:ASA5515 using 9.6(4)42Spoke sites:Cisco ISRs using 15.1(4)M8, using voip services over ...
Trustsec Network Authorization not Working
Hi All,I am newly building trustsec in my environment,trying to add one of the switch under trustsec. Have configured Trustsec settings and COA on the ISE for the switch and added the appropriate aaa commands , radius servers and cts commands.But sti...
Resolved! IPSec Agressive mode, and Crypto Map
Hi, how are you :). I have one question, about router Cisco 2911, and Juniper Netscreen 25, ver 5.4. I must start IP Sec tunnel between these two devices. I must use agressive mode, I saw this in configuration document. Question, how can I use agres...
NCS5504 line card not detected after Upgrade
I have upgraded cisco NCS-5504 router . Router was successfully upgraded but all the line cards are not showing. In platform command type is unknown and state is SW_Inactive.Regards Salman
| User | Helpful Count |
|---|---|
| 107 | |
| 106 | |
| 85 | |
| 70 | |
| 60 |
