When is the appropriate times to use ' or " when creating message filters?Is ' used when you are adding in your own string of characters and " used for a system defined item like in the following example? header ("From") == 'example.com'
Greetings! Hope somebody can guide me how is it supposed to be done! Sorry, I'm a noob and seems to can't find an answer.Lets say I have 3 subnets/vlans/interfaces with security levels:inside (90)dmz (10)outside (0)lets say I want to allow http/https...
My FTD (FDM) running code 7.2.5.1-29 is getting the following message on the Smart License section: CONNECTION ISSUEFailed To Connect With License Server Lost connection for 0 days (Next Sync on 28 Mar 2024 11:06 PM). Please check and make sure the m...
I am looking at the following example in the admin guide:The remote-ip rule tests to see if the IP address of the host that sent that message matches a certain pattern.The IP address can be either Internet Protocol version 4 (IPv4) or Internet Protoc...
Hello,I have a question about migrating a IPSec tunnel from between a Cisco C981F-k9 and a Cisco ASA firewall to a tunnel from the same Cisco C981F-k9 router to a Fortigate firewall. What is the 'best' way to migrate this tunnel?Currently I have conf...
I am creating Deployment Profiles from Secure X in order to push Secure Client (and our modules) to workstations and servers. The deployment profile for workstations works as expected, whether using a Full Installer or Network installer. I am now t...
Hi,Our network only consists of Meraki products and now we are looking at the possibility of implementing 802.1X on wired and using Cisco ISE for that.Our business is geographically very spread out and we have both large and small branches. Some smal...
Hello community, i have a question, but can`t find answer on it. If we have one listener for inbound and outbound communication and this private IP has NAT to public IP. We don`t have communication to mail server on private IP. Is it a problem if ...
Hello I am working with a network that has currently 10 router nodes using IPSec tunneling to communicate and encrypt packets between the 10 router nodes over a wan. Using 140.0.0.0/30 (64 tunnels total) for IPSec Tunneling I have consumed almost all...
Dears, i am not able to see all the acls with object groups on gui , however in cli i am able to see all acls applied. i have an issue with checking and modifying the acls on gui ( note that i upgraded the switch to the v17.9.4a ). Need assistance pl...
I have two Firepowers in two remote offices and i have two ISPs in each office, i had configured vti ipsec vpn between two offices but they are working with static routes, can i configure dynamic routing protocols for failover vpn? I tried to configu...
HelloWe've successfully enabled the ISE Guest Portal on our WLC, and it works well with PCs until we apply explicit proxy settings. After configuring the proxy, the guest portal no longer appears; instead, the PC tries to access the proxy server, byp...
FMC: v7.3.0 (build 69)FTD 1120: v7.2.5ISE-PIC: 3.2.0.542, Patch 4We have a new integration between ISE-PIC and FMC that we are trying to use in policy. I can see some users are shown in the Unified Events, but many entries show as "Not Found". For on...
Hello all,When looking at show auth sessions int gx/x detail , I see a field called acct update timeout , and ours is set to 300 seconds with a countdown timer.My questions are:What does this field mean?What resets the countdown timer?How can you cha...
Hi,I wonder if there is a way to send every incoming and outgoing message both to the original destination and to another destination for analyses. Preferably before any scanning or policies interfere.I've tried google, but have not come up with anyt...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: