FindIT Network Management Discussions
Join the FindIT Network Management discussion community and gain valuable insights from industry exp...
63 PostsActivity in Small Business Support Community
FTD intervlan questioning,
Scenario,Host-A(10.10.30.3/24) connects to access port on SwitchA with various other vlans also configured via access ports. SwitchA connects on a Trunk port to a CatSwitch. Firepower inside ½ interface trunks to CatSwitch. On The CatSwitch 3 vlans; ...
initializing network
hello, we have a cisco spa504g at my work place connected through Telstra. it has been saying 'initializing network' for 2 days now and the microphone button is red. we have tried resetting/restarting in each and every way but no changes. also the ph...
Need help with Cisco SPA 112.
I have recently bought a SPA 112, and arrived yesterday, I was able to get into config settings, i factory reset it, its the same ip but when i look it up its not working. I need help with this, and I Think it might be company locked. I really need h...
Switch power shuts down on it's own
We have a Cisco Switch 350 that just powers down on its own. The logs do not show anything as it is a limited log and cleared when it powers off. It happens often and it's not a power outage or power brownout. The switch is also on a good UPS and we ...
Retrieve Serial Number Info for Cisco WAP4410N Access Point
Hi,I have tried to retrieve serial number info for 3 units of the Cisco WAP4410N Access Point devices via Web GUI and CLI, but it seems can't find the serial number info for this model. Kindly advise further, thanks.Regards,Wilson Leong
How can I delete a fixed profile rule in a Linksys ATA?
I have a Linksys SPA2100 ATA that I used with a previous VoIP provider. I did a factory reset but their profile rule is still listed in the first Profile Rule section under the Provisioning tab. Profile Rule B, C and D are blank and I can enter a pro...
SPA2102 Line 1 "Not Registered"
The SPA2102 is running firmware 5.2.5. Line 2 works fine. If I set up line 2 incorrectly, I get "failed" as expected. Line 1 is another story. No matter how I set up line 1, the status remains "Not Registered". It would seem that the line is not enab...
cisco room meeting navigator panel didnot take network
Hi,when i connected cisco navigator panel to codec kit plus it shows 'has not yet received DNS address from DHCP' and i tried to connect with wifi but the wifi doesnot work because i disconnected the ethernet from codec and check with navigator panel...
Resolved! Remote access to voicemail box UC320W
Is there a way to access your messages from outside the office? I have tried *, # and looked at our options but do not see anything refering to outside access.
SG500 not saving config after removing VLAN tags from ports
Hey there, We use some SG500s here and I can't get them to work with our VLANs. We have some ports on our switch that are tagged with VLANs, but whenever I untag them using the GUI, I can see the changes being made when I telnet into the switch. I th...
Cisco Business Dashboard API Swagger file is missing
Hello, The Cisco Business Dashboard API Swagger file is missing. The link on the API reference page for Swagger file is broken/missing (Return code 404) Source: https://developer.cisco.com/docs/business-dashboard/#!api-reference Resources Support ...
RX channel fiber port
hi, I have to acquire the signal from SFP with fiber port and redirect the signal to ports number 47 and 48.the problem is that only with the transmission cable connected to the SFP, the port does not light up and the signal is not processed.How can...
Resolved! All Cisco RV Routers EOL. Perhaps new CBR line coming?
So the Cisco Small Business RV340, RV345, RV 160, RV260, RV345P, RV340W, RV260W, RV260P and RV160W VPN Router has all reached EOS & EOL. That's every small business router that Cisco currently has. Per Cisco, there is currently no product migration...
SPA525G2 Not Pairing To Bluetooth
I have an SPA525G2 desk phone that will not pair to certain headsets. Sometimes they do not even show up in the scan list. I updated the firmware to 7.6.2f using the Bluetooth firmware version but it did not help. Hardware version is 2.1.1The headset...
Resolved! configuration cisco 140 AC access point
Hello Team.I have a problem with the Cisco 140 AC access points that I am installing at a client's home. We have followed the configuration procedures:- we created an administrator account-I created a wireless network- I confirmed the settings- when ...
| User | Helpful Count |
|---|---|
| 3 | |
| 3 | |
| 2 | |
| 2 | |
| 2 |
