Cisco Catalyst Center
This community is for technical, feature, configuration and deployment questions. For production dep...
2136 PostsActivity in Networking
Catalyst C2960-C Essential Licenses SKU
Hi Community, According with the below document, switches C2960-C are supported by DNA Center. https://www.cisco.com/c/en/us/support/cloud-systems-management/dna-center/products-device-support-tables-list.html Can you please confirm the SKU of the ...
QOS for a Destination-ip in Cisco IOSXE
Hi All,We have a URL which resolves to particular public ip and performance of that website is slow than expected from our office . We have a P2P link from office to DataCentre and from DataCentre it exits to internet. We observed the performance was...
Cisco cellular Gateway stuck in green blinking
Hi all,I am installing a cisco cellular gateway CG522-E and after installing the sim card and powering up, the gateway ends up with the led flashing in green without moving to blue. I have tried removing and reinserting the sim card, powering up agai...
Cisco DNA Center Telemetry
Hallo All! What is the reason that when enabling Telemetry on C9300 Series Switches, only Application Name, Usage and Througput are shown? Switches configured with telemetry show only Application Visibility (Name and Throughput) in DNA center. Why is...
destination address is the broadcast address within matched route
Please see attached pic. In this question, the destination address matches the route in the routing table. But it's the broadcast address within that range. Would the packet still be routed with that route?what would the next hop be? 192.168.0.7 or 1...
Nexus 93108TC-EX - %DAEMON-3-SYSTEM_MSG: Error
Hi, We upgraded our Nexus-93108TC-EX devices to software version 10.2.4.M and now we are receiving the below warning message. I believe this is a bug , how can we resolve this issue? Any assistance would be greatly appreciated. 2023 Apr 18 14:10:58 ...
Need some assistance with some basic VLAN/Routing config Cisco 1941.
Hi all I'm setting up a CISCO LAB to keep me busy in my retirement. My Current network consists of a TP-Link Deco mesh network which works well for my IOT, PCs and internet access. I just got hold of a Cisco 1941 router with a EHWIC D8SGP module. ...
vlan interface administratively down
I just created a vlan, assigned it to a port on our 6509, assigned the vlan an ip address and when i shoot the command, show int vlan 31 it says that the vlan is administratively down. I can't figure out whats going on here? i issued a no shut, to no...
Cisco2960X IBNS 2.0 and 802.1x/MAB Authentication NOT working
Hello,i was successfully deploying Nac configuration on all my switches when i encountered i problem with the new authentication display config-mode on a WS-C2960X-48LPS-L 15.2(7)E4:SwitchplanA#authentication display config-modeCurrent configuration...
IP SLA Monitoring MIB
I've setup an icmp-echo IP SLA on a Cisco C9300 to ping another device on our network. I'm now trying to monitor the amount of timeouts seen by the IP SLA job in our monitoring tool (WhatsUp Gold) but when setting up the monitor, the issue I'm having...
Unable to get console access on switch 3850 - Blank terminal
Hello,I have a switch I am unable get a prompt on the console port.I can SSH to it, and have confirmed that the baud rate and stop bits are correct from the console switch. There are two other switches that I can console to.The differences are that t...
Please explain those terms. I can't understand. Help needed!
"Distribution Switch for Formation" & "Enterprise and Active Directory (AD) Zone Switch"
Simple SSH Connection 9400 Not Working
Is there something different about configuring SSH on a 9407 with a C9400-SUP-1? Currently there's no configuration on the device except for an IP address on the management port and ssh. I've gone through the same procedures we've always used and v...
Catalyst 1000 / secureing management access
Hello,I am still considering wheter to deploy Catalyst1000 or CBS350 switch at our small office(15-25 devices).Switch have to be configured with multiple SVIs and DHCP server pools for each + few static routes.I would like to secure MGMT access to th...
DMVPN Spoke not connecting when using starlink
I have set up as above. I am using starlink at one of my spokes. I am not able to get to pass VPN traffic even though show dmvpn shows that the vpn is up.
| User | Helpful Count |
|---|---|
| 59 | |
| 41 | |
| 38 | |
| 37 | |
| 34 |
| User | Count |
|---|---|
| 32 | |
| 17 | |
| 14 | |
| 13 | |
| 10 |
