Wireless - Mobility

Connect with peers and Cisco on all aspects of wireless tech including security and network management, LANs and indoor and outdoor access points.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Browse the Community

Activity in Wireless - Mobility

Configuring and Managing C9130AXI-B Access Point

I got a couple of C9130AXI-B Access Points to build a small Wi-Fi network (2-3 Cisco APs). I thought it has the Embedded Wireless Controller as stated in the Data sheet for the 9130AX series or did I get the wrong part number and I should have bought...

ybp2000_0-1711747089829.png
ybp2000 by Level 1
  • 79 Views
  • 1 replies
  • 0 Helpful votes

C9800 wlc Mgmtuser encrypt password

hi,the mgmtuser username password defined in my AP join policy show in clear text and cannot be encrypted.when i exe the command,mgmtuser username admin password 8 mypass123 secret 8 mysecret123always get error %password encryption failed: possible m...

AP4802 displayed as 3802 in mobility express

Hi, I just did a deployment with some 4802APs, but in the mobility express GUI (as well as in the APs CLI) they are showed as 3802, anyone an idea how that can happen?I just uploaded the AIR-AP4800-K9-ME-8-10-190-0.tar on the AP functioning as Contro...

Resolved! WLC 8510 HDD failure

We had one of our HDD fail and now the device won't boot at all.  We can get into IMM and we are also able to use KVM to view the BIOS boot up and menu system.  I've tried to boot off USB, CD ROM, and the other HDD but I cannot get this device to boo...

netgn by Level 1
  • 80 Views
  • 1 replies
  • 0 Helpful votes

WLC 9800-40 Disable IPv6

Hello  everybody,  sb know, how to disable IPv6 (CLI) on WLC9800-40? SW 17.4.1 IOS-XE Bengaluru. GUI Global Config do not works.  Thanks a lot. 

9166 clients not connecting at 5 GHz

9800-80 pair running 17.9.4a and APSP8 (upgraded about a month ago). Upon investigating after slowness/connection complaints from the professor of a 150-seat lecture hall where 9166s are installed, I realized that every single client in the room was ...

eglinsky2012_0-1706559000236.png

Poor 5Ghz throughput - 9800 / 17.9.4a / 1800-series APs

Hi,Per the title, I've got an issue with 5Ghz clients that have good signal strength because they are sat almost underneath the AP (1832 APs) yet but struggling to get more than 1Mbps throughput.  I can see the channel utilisation is over 50% but zer...

Resolved! WLC CLI command to show clients

Hi everybodyI work with a Cisco 8540 WLC and I have to extract some connection statistics.Is there some command to list...- all clients connected to a specific SSID?- all clients connected to a specific APGroup?- all clients connected to a particular...

Aleck_Sei by Level 1
  • 6067 Views
  • 4 replies
  • 0 Helpful votes

AIR-AP2802I-E-K9 fail to join

Hello ,We are having problem with one AP to join the WLC , all others successfully the controlle. the console output is :[*03/19/2024 09:08:50.0003] CAPWAP State: DTLS Setup[*03/19/2024 09:08:50.0035] dtls_process_packet: DTLS Error: 1040[*03/19/2024...

zillams by Level 1
  • 183 Views
  • 5 replies
  • 0 Helpful votes

C9800-80 in HA cannot install APSP6

Hello everyone,I'm trying to figure out a frustrating issue. Attempting an install of APSP6 keeps bombing out and I'm unsure what steps to take next. Software: Version 17.09.04aROM: 17.3(3r)Error in question:  Dec 13 21:21:01 Eastern: %INSTALL-3-OPER...

Resolved! Flexconnect on wlc 9800

Hi,We have a pair of 9800s in HA/SSO. About to migrate our APs from 8540 to 9800. As im recreating our SSIDs to the new 9800s, we cant get the one flexconnect SSID to work. The 4 centrally switched SSIDs work as expected. I have followed the various ...

trondaker by Level 1
  • 223 Views
  • 6 replies
  • 0 Helpful votes

Resolved! Access Point

Hi all, can the cisco catalyst AP model 9136I, act as Autonomous.

9800-L WLC Controller and CA Signed Cert Web Server

Does anyone have a Cisco 9800-L WLC Controller and successful installed a CA Signed Cert for Web Server? Not making the Certificate signing request, but actually already have the PEM and other files locally. Cisco TAC can't figure it out. The documen...

No console port connection

I am using a cable from Console to serial, and that cable connected from serial to usb and i am using PuTTY. I have tested this setup with a Catalyst 2960 switch and i got output, but when i am using the same configuration for the 2504 Wireless contr...

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Top Experts - Last 30 Days