Wireless - Mobility

Connect with peers and Cisco on all aspects of wireless tech including security and network management, LANs and indoor and outdoor access points.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Browse the Community

Activity in Wireless - Mobility

5/6GHz. One SSID to rule them all, or separate?

So, this is more a question of what people are using or seeing. We will be replacing all our facilities this year and I plan to go Wi-Fi6E. I have tested having the SSID with mixed, but I have also heard separate doe to if a client shifts frequencies...

Google Home Mini on Cisco 9115 APs

I have a single google home that will not stay connected to wireless. This is a network consisting of only two 9115aps and nothing else in the network its having the issue. There is a single google home that disconnects daily and will not reconnect t...

jeremy0463 by Spotlight
  • 262 Views
  • 9 replies
  • 0 Helpful votes

Assistance configuring multi SSID Air-lap 1142

I need some help with configuring an autonomous 1142 ap. I enter the GUI set up two vlans 100 and 200. vlan 100 has corporate wifi and vlan 200 has guest wifi. I signals appear on my phone but when i go to connect to them I don't get an IP address. I...

WLC config for eap-tls wifi

HI all, we are deploying a wireless eap-tls machine authenticated network. We have a PKI using Windows CA services with one offline root CA and one intermediate issuing CA. For our RADIUS server, I started with a windows NPS server and then changed i...

jessegarcia11_3-1710782192960.png jessegarcia11_4-1710782252183.png jessegarcia11_0-1710781740949.png jessegarcia11_1-1710781769548.png

Resolved! WLC 9800 HA N+1 - AP not falling back to primary WLC

I have a very simple setup: WLC1 (172.16.0.250) = Primary BACKUP (172.16.0.251) = Backup When the Primary goes offline, my AP moves to the BACKUP wlc as expectedHowever, when the Primary comes back online, the AP remains in the BACKUP and does not "f...

Resolved! Setting a wpa2 Password on Cisco 1142

Have an autonomous ap im configuring for use. When i enter the password in ASCII format it tells me I can't use a ? character. Is there any way around this? This is my software version,Cisco IOS Software, C1140 Software (C1140-K9W7-M), Version 15.3(3...

what b L a means on AP map AP icon please?

greetings,i was wondering what b L a means in an AP Icon of AP map please?a - 802.11ab= 802.11b per what i know but "L", i don't know. best Regards, Masood

MasoodA by Level 1
  • 144 Views
  • 4 replies
  • 0 Helpful votes

AP wont change to Flex Bridge mode on the RAP

Objective is to build a point to point Mesh Bridge with 2 c9124 AP's one running a EWCRunning version 17.13.1Currently I'm configuring a point to point bridge with two c9124 and one is configured as an ewc. the ap mode is only showing as flex and if ...

Resolved! Improving Wireless Performance

I have been getting lot of complaints from the C-level about the speed of the wireless network.  Tests on the wired network yield 700+ Mbps but the wireless strains to reach 24 Mbps.I do not expect the wireless network to match the wired network in s...

Resolved! CISCO wireless tools

Hi all,I need a little clarification about Cisco wireless tools.Cisco WLC is basically to configure wireless network(ap,ap groups,radius,etc),isn't it?But when I need to monitor APs,clients,RFs,channels,etc...,Cisco WLC is not really "friendly",basic...

gabelz by Level 1
  • 234 Views
  • 6 replies
  • 0 Helpful votes

3802 AP LED turn off after registered with WLC

The LED light of 3802 AP is off after registered with 9800 WLC . But the 3802 access point is still working perfectly in providing the wireless connection to the end device .  We have factory-reset the AP and issue remain the same after the AP regist...

ANT2566D4M-RS antenna and warehouse

Hi,what it is your experience with this antenna in warehouse environment especially for areas between racks? What else did you used it for?How do you choose antenna based on gain for areas between racks? For example, if this area is 60m or longer, wo...

iores by Level 1
  • 181 Views
  • 4 replies
  • 0 Helpful votes

Resolved! Joining 3802s to a 2504/5508/5520 after it has been on a 9800

Scenario:We rented a building that already has a ceiling full of 9800s.  When we took occupancy, everyone thought the 3802s would join the 5520.  Nope.I put a borrowed 9800-l online, and APs would join it.  Reconnect them to the network where the 552...

denneht by Level 1
  • 474 Views
  • 18 replies
  • 0 Helpful votes
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Top Experts - Last 30 Days