Wireless - Mobility

I acquired 2 aps cisco 9120ax from one soon to the next, it does not g

what's the algorithm for interface groups assingments on wlc 5508?

I'm trying to find a trustworthy source about the assignment algorithm of wireless traffic when many wireless clients send traffic to WLAN associated with an interface group, let's say with 4 VLANs. the documentation below doesn't say anything about ...

C9800-80 in HA cannot install APSP6

Hello everyone,I'm trying to figure out a frustrating issue. Attempting an install of APSP6 keeps bombing out and I'm unsure what steps to take next. Software: Version 17.09.04aROM: 17.3(3r)Error in question:  Dec 13 21:21:01 Eastern: %INSTALL-3-OPER...

Wireless IOSxe Client Ioslation and multicast

Hey everyone,Questions - on a guest WLAN I have client isolation enabled via the Peer to Peer blocking action to drop.  I can see it blocks peer to peer unicast traffic, however multicast traffic between peers still flows.  I can limit the mdns messa...

Can I change the regulatory domain for our new CW9164I-ROW AP?

We have a 9800-CL Wireless Controller running 17.12.2.  We just got a new CW9164I-ROW AP and its registered by the operational interfaces are down due to a regulatory domain error.  Is there a way to change the regulatory domain for the access point?...

AP-AIR2802i-B-K9 No join

l installed newest version of Wireless controller 9800-CL Cloud but wont Join DTLS Error l dont why it wont join to controller 

Wired Guest issues in foreign-acnhor setup

Wired guests are not able to get out to internet, they can ping only at when payload is set to 1300 bytes or lower, this seems like an MTU issue, but its only effecting wired guest not wireless guest. Setup is a 9800 foreign on 17.9.5 code and 5520 a...

WLC, SSO and OEAP

Hi I got a pair of 5520 in SSO mode version 8.10.190. If you want to run OEAP then you need to enable Enable NAT Address on the management interface. The problem is that the "Enable NAT Address" is greyed out: the question is: is it possible to enab...

Spaces Telemetry issues

I'm trying to get environmental stats back from 9136/9166 on Spaces. I've imported the maps successfully and have enabled the IOT service in spaces. I'm still getting errors for the TDL Telemetry under the troubleshooting section which seems to be pr...

WLC 9800 - ignoring client - [rogue-core]

Hello,I've got question related to this particular debug entries (from radioactive trace):2024/04/18 13:06:43.944436 {rogued_R0-0}{1}: [rogue-capwap] [25943]: (debug): Client info (2/2), MAC:<xxxxxx>, reported by yyyyyyy, GW: 111111111, chan:40, rssi...

cisco 2504 WILAN ERROR MESSAGE

  Dear All.,My Cisco WLAN CONTROLLER 2504 suddenly started to De-associate Access Points. Attached herewith is the Error Message gotten from the GUI Let me know if anyone has solution to address this thanks.

RF Heat Maps not shoiwng in Prime 3.10

Hi, We have recently deployed Prime 3.10.2 and added a 9800-L (SW 17.6.4) along with 10 X 9130 APs.. On adding the APs to the site maps within Prime, there is no RF heat maps being emitted from them. Just wondering if any has come across this issue a...

AP Alarm

 What is the meaning of this Alert and what can I do to mitigate this. (for Unified Access Points)Message: '802.11a/n' interface of AP 'XXX' associated to controller 'XXXX)' is down. Reason: Radio reset due to (56) Radio channel set