Cisco Catalyst Center
This community is for technical, feature, configuration and deployment questions. For production dep...
2136 PostsActivity in Networking
Cisco2960X IBNS 2.0 and 802.1x/MAB Authentication NOT working
Hello,i was successfully deploying Nac configuration on all my switches when i encountered i problem with the new authentication display config-mode on a WS-C2960X-48LPS-L 15.2(7)E4:SwitchplanA#authentication display config-modeCurrent configuration...
Please explain those terms. I can't understand. Help needed!
"Distribution Switch for Formation" & "Enterprise and Active Directory (AD) Zone Switch"
Need some assistance with some basic VLAN/Routing config Cisco 1941.
Hi all I'm setting up a CISCO LAB to keep me busy in my retirement. My Current network consists of a TP-Link Deco mesh network which works well for my IOT, PCs and internet access. I just got hold of a Cisco 1941 router with a EHWIC D8SGP module. ...
Catalyst 1000 / secureing management access
Hello,I am still considering wheter to deploy Catalyst1000 or CBS350 switch at our small office(15-25 devices).Switch have to be configured with multiple SVIs and DHCP server pools for each + few static routes.I would like to secure MGMT access to th...
DMVPN Spoke not connecting when using starlink
I have set up as above. I am using starlink at one of my spokes. I am not able to get to pass VPN traffic even though show dmvpn shows that the vpn is up.
Migrating Cisco IOS Config to Nexus
I know that there was a tool a couple of years ago which migrated config from Cisco IOS to Nexus but it doesn't look like this is available anymore. Is there anything else around which can migrate the configuration? Python script or similar? https://...
Redundancy Over VSAT Link
Hi, we have a WAN and VSAT connection to one of the site. WAN is primary and VSAT is secondary link.We have dedicated router for WAN and VSAT. VSAT link is connected to one of the LAN access switch.Could you please help me, what kind of configuration...
SSID not discoverable by laptop in Packet Tracer
We have configured two Lightweight Access Points using a 3504 WLC. Both access points are connected to the WLC, and have been assigned IP addresses through DHCP from the WLC. Both also state they are providing the WLAN we created. Authentication for ...
4506 dhcp issue
we had a daily-basis ip conflict with dhcp server on cisco switch 4506E specially after replacing some the users' ports or a user using the laptop and moves alot, the ip conflict is detected using GARP method.note: the user could try multible free IP...
Migrate subnet into SD Access
HiI am testing migrating a subnet into SD Access. I have a subnet routed outside my fabric and I have a device inside my fabric on that subnet routed by the external gateway by handing off the address pool on a L2 VN. This all works fine.I now want...
SDA L2VNIDs
Hi All,Quick question hopefully. I noticed that when DNA Center provisions a L2 network within a fabric site, its allocates a L2VNID starting 8188 for local segments and 16196 for multisite remote border/anchor VN segments.If I remove and re-add an p...
how to onboard the SDA Fabric Edge which is using stackwise virtual
Hi , Thank you so much . Does anyone have any idea how to onboard the stackwise virtual into fabric , as of today LAN automation is not supported.Im thinking of below approach , really appreciate your valuable suggestions. 1> Manually configure the...
Telemetry Data on 9300 Switches (App Visibilty and Experience)
Hallo All! What is the reason that when enabling Telemetry on C9300 Series Switches, only Application Name, Usage and Througput are shown? Switches configured with telemetry show only Application Visibility (Name and Throughput) in DNA center. Why is...
Cisco cellular Gateway stuck in green blinking
Hi all,I am installing a cisco cellular gateway CG522-E and after installing the sim card and powering up, the gateway ends up with the led flashing in green without moving to blue. I have tried removing and reinserting the sim card, powering up agai...
VRRP issue
Facing issue with VRRP, when upstream router5 initiate traffic for downstream router6 then return traffic is not following VRRP VIP as Gateway. In my case switch2 is master and switch3 is standby.If Router6 initiate the traffic then VRRP working fine...
| User | Helpful Count |
|---|---|
| 59 | |
| 41 | |
| 38 | |
| 37 | |
| 34 |
| User | Count |
|---|---|
| 32 | |
| 17 | |
| 14 | |
| 13 | |
| 10 |
