Cisco Catalyst Center
This community is for technical, feature, configuration and deployment questions. For production dep...
2151 PostsActivity in Networking
1921 Router Config Help
Hello, I know very little about configuring cisco hardware and need some help..... we are currently running an 1800 router and I obtained a new to me 1921 router and would like to replace the 1800 router with the newer one, I managed to get it factor...
Repeating syslog Message and then Crash
We're seeing a continuous string of the following messages on a 9407 running 17.9.5. Eventually the switch crashes. I can't find any info on what these messages mean exactly and whether we're looking at a software or hardware fault. The supervisor...
copy xmodem initializing no transfer c2960
Hi Guys, i had this problem for 8 hours now and can't seem to get it cracked... after i input the command copy xmodem: flash:c2960-lanbasek9-mz.152-7.e9.binand using the SecureCRT going to Transfer > send xmodem I get this and after that nothing happ...
Catalyst center backups
HiCan I jusy clarify some backup information please? The automation only backup is what you would restore if your cluster went awol and you are recovering all your fabric info? Device configs, hand offs, port allocations, L2/L3 VN info, SGT matrix ...
Trunking an ip addressed inside interface on Firepower 2130
My network endpoints use the IP addressed vlans on my core cisco layer three core switch as their gateway addresses. i.e.- vlan 11 endpoint address 192.168.11.3/24 with gateway 192.168.11.1/24 (vlan ip on core) and vlan 12 endpoint address 192.168.12...
Resolved! How can i match vsmart with each Tenant
Hello team Last day i upgraded all controller in to 20.3.5 -> 20.6.5 version as you know in 20.3.5 which use multitenant mode , the vsmart are bind in each tenant. but when i upgarde it 20.6.5 version. the vsmart are come out side. I want to use th...
Unable to Access Web Server - Whats Wrong with this Configuration
ASA working in IPSec, I am able to access HQ from UNIT No problem. Internet is only allowed on specific IPs which are outside DHCP Scope. When I assign IP for internet, now Internet is working, HQ Network is accessible, but S_EXT (webserver - 10.10.1...
loopback for traffic measurement
I am trying to measure a link speed I have a traffic generator machine.I want my Cisco ASR-1001 to loopback the traffic to the generator,What config do I need to use?I am trying to do it in Layer 3 and there is a switch in between.
VPN - Geo-Location Based Traffic Management
Hi guys,My company has branches in 3 locations (the US, China, and Canada). I want to create a FULL-TUNNEL VPN for users who connect from coffee shops, airports, and hotels.I will do it using the Cisco profile editor and call it a UNSECURED VPN profi...
NTP and Syslog packets with specific IP Address
Hi All,I have a couple of C9300 L3 switches that are connecting to an ASA firewall. The NTP and the syslog server for the switches are located behind a firewall.When one of the switches request/send packets the gateway IP is the source address on the...
Resolved! Best practice lan configuration
HiI have 4 Cisco 2960 switches and 3 unmanaged switches. All are connected via fiber cable to a core switch 4503-3 and it is connected to a VPN router and internet router. (still don't have access to the routers yet)I know I have to replace the unman...
Resolved! DMVPN Spoke not connecting when using starlink
I have set up as above. I am using starlink at one of my spokes. I am not able to get to pass VPN traffic even though show dmvpn shows that the vpn is up.
Cisco Switch Web UI with HTTPS (lock icon)?
Hello, has anyone successfully implemented HTTPS on their switch web management UI? I would like to get rid of the warning when I access the web UI, but I cannot seem to find resources about it online.I am currently using a Catalyst 9300 in my networ...
Forward traffic from subnet to another on C3750
hi guys thanks for your suggestions in advancei just reconsidered my whole message. after trying some things. i think i need to set up acl but i'm far from good at it.what would be the ip access-list extended or access-list lines that'd allow me to h...
Resolved! Certificate install issue WLC DNA
For some reason one of our pair of WLC 9800 will not accept DNAC-CA certificate.A sync or push of telemetry from DNA fails. All our other devices are fine.If we try a CLI import of the certificate we get this:Trustpoint 'DNAC-CA' is a subordinate CA....
| User | Helpful Count |
|---|---|
| 69 | |
| 40 | |
| 39 | |
| 36 | |
| 33 |
| User | Count |
|---|---|
| 24 | |
| 16 | |
| 16 | |
| 11 | |
| 10 |
