You asked, we heard you! Introducing the ThousandEyes Support Community Capture the Flag event from April 23rd at 8 AM PST to April 29th at 5 PM PST. This month the ThousandEyes Community is offering two Capture the Flag missions in a single upcoming...
hello, So in my lab i just have 3 CEDGE (CRSv) and i want to connect them to the controllers the only consideration is that the link are MPLS ONLY or in this case i put gi1 color private1 and gi2 color private2 on the SDWAN-DC device and i created r...
Where do i find the complete guide on my switch?This is the model number WS-C2960X-48FPS-L.The software version is c2960x-universalk9-mz.152-2.E3What I'm looking to do is limit how much bandwidth is allowed on an interface. The network at that site o...
I have a cisco sg350-10 switch with 2 sfp modules.Which brand suggestions would be compatible modules for a sfp rj45 connectors?can you send me the link of the manufacturer , brand or model suggestions?Any help would be appreciated.Thanks.
Hi All,We have a URL which resolves to particular public ip and performance of that website is slow than expected from our office . We have a P2P link from office to DataCentre and from DataCentre it exits to internet. We observed the performance was...
Hello, I was creating 2 decently large ACL's to match some traffic today and I noticed something peculiar that has me puzzled. My first ACL has approx 90 ace's and pastes them fine. When I go back and look at the ACL, it looks like there are only lik...
hi guys . i have a network with below topology. In the core layer, I want to have redundancy, which means that if the main core switch of my network has a problem, the backup switch will automatically enter the circuit. What method is there?
The route learned by OSPF from the LAN is re-distributed to OMP for publicity to other sites.I do not want to advertise the specific routes from OSPF. What kind of 'configuration' should we use ?I want to control this in the SD-WAN Router side, not t...
Hi everyone.. i have been looking through multiple posts on the forum for similar cases but have not found the answer Im looking for.. I've been primarily using this thread for guidance. https://community.cisco.com/t5/networking-knowledge-base/settin...
Hi I'm trying to extended a L2 segment using MPLS L2vpn over GRE. I am able to establish the tunnel and get ospf and mpls adjacency also the xconnect between the peer is up but my 2 test pc cant reach each other. This is my PE3 config.interface Gigab...
We have a Cisco ASR1001-X and it can only pass 750 megs of traffic thru it on a 10 Gig circuit. I looked at licensing levels and they seem correct. Anyone have any ideas of what I can look at? Both Lan and Wan interfaces are 10 gig and Wan is using S...
Hello, I am working on collecting BGP-LS SAFI using BMP towards Cisco's opensource project Jalapeno. I have captured packets between RR and Jalapeno on each use case to observer where we see BGP-LS and where we DON'T see BGP-LS packets. few use cases...
Hi,We currently have a mix of Cisco switches from 2960s, 2960X and now the 9200L. However we are having issues with our Paxton POE door controllers. The 2960s work with all of our Paxton ControllersThe 2960X up to hardware version 4 work with the Pa...
Hello everyone, I have two cisco 3750 switches that are on stack with the below config Switch# Role Mac Address Priority State--------------------------------------------------------*3 Master 0017.5ae7.d500 1 Ready4 Member c062.6b8c.f200 1 Readyi wou...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: