Service Providers

Explore information and join discussions with peers and Cisco about Next-Generation Internet, MPLS, voice over IP and Visual Networking Index.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Browse the Community

Activity in Service Providers

Segment Routing Prefix SID

Hi All,I found in Segment Routing Architecture RFC 8402 "A BGP-Prefix segment is global (unless explicitly advertised otherwise) within the SR domain.""An IGP-Prefix segment is global (unless explicitly advertised otherwise) within the SR domain." Bu...

ASR1001x and Lawful Interception

Hi all,I've been tasked with setting up a Lawful Interception solution for our company.  I have read quite a few documents and googled the crap out of this but for the life of me, I can't get the basics working.My intention at this early stage is to ...

Resolved! BGP Flowspec ASR9901 support

Hello all, I have a question, have someone tested the BGP flowspec client on ASR9901 ? It's IOS XR 7.1.3.I am correctly receiving FS prefix from remote FS controller but it is not programmed to hardwareRP/0/RSP0/CPU0:asr9901#show bgp ipv4 flowspecNet...

Cisco Catalyst 8000v as an ISP Edge

We have a requirement to have a virtual router in a Colocation Data Center in Europe. The model we were given by the provider is Catalyst 8000v Autonomous Mode.We need to connect an IPT to it and receive multiple full BGP table instances (multipath) ...

MPLS to cloud Migration

My company is going to be migrating from on prem to an all SaaS world. We currently have a DC that will be going away in the next year and about a 1/4 of our locations will be moving off MPLS to DIA circuits with Meraki equipment. For the sites that ...

Resolved! Show alarms on 64-bit eXR for ASR 9000

Hello,In 32-bit Classic IOS XR, one could easily view the status of craft interface LEDs (e.g. alarm lights on RPs and front panel, etc) by running the "admin show environment leds" command. However, this command is no longer supported for ASR 9K pla...

James Jun by Level 1
  • 5559 Views
  • 4 replies
  • 0 Helpful votes

Resolved! Segment Routing SR/LDP interworking problem with NX-OS

Hi All, I have created a lab in EVE-NG to test SR-LDP interworking. I configured an SR Mapping Server to advertise prefix-SIDs on behalf of non-SR routers. Only routers that run XE/XR software can get prefix-SIDs from the mapping server without probl...

XR 9k route-policy impact question

All, I have a simple route-policy I'd like to apply to a set of peers.This would be applied to 25k prefixes in the bgp table.Given no ios-regex is being used in the route-policy, I'm looking for any expertise on potential impact/load on the system. I...

Resolved! accessing admin exec mode

Hi all, I am having a problem to access the admin exec mode of an asr 9000 which runs 6.5.When I give the admin in exec mode it transfers me to RP/0/RSP1/CPU0:x1#adminadmin connected from 127.0.0.1 using console on x1sysadmin-vm:0_RSP0# exit Thanks i...

mac87 by Level 1
  • 1725 Views
  • 7 replies
  • 0 Helpful votes

Flowspec problems in NCS5500

Hello,I am implementing flowspec on an NCS 5500, I accept the rules through eBGP. I am having problems because although I receive the routes correctly and I see that the TCAM has entries. The problem is that I am observing that the entries are not ha...

Errors when debug voice application error is enabled

On an ISR G2 running CME, when "debug voice application error" is enabled, the logs are continually flooded with the error://-1//TCLM:/tcl_hunt_group_num_calls_in_callq: B-ACD-SERVICE Tcl service not availableI have tried installing the b-acd scripts...

Remote Phy-Docsis OFDM issue

We have several Remote Phy shelves deployed (RPD shelves) in our CO's feeding our nodes running DOCSIS 3.0 and OFDM. Customers with 3.0 modems obvisouly link up with the traditional DS channels. Our 3.1 modems lock on to the OFDM band as well. Random...

jhuffman by Level 1
  • 114 Views
  • 0 replies
  • 0 Helpful votes
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: