Activity in Security
Suspend button for AnyConnect
Hi, My company is unwilling to set up split routing, for security reasons. Therefore, they ask us to disconnect from the VPN for bandwidth-intensive activities like VoIP and file downloads. This is cumbersome, as reconnecting requires us to input our...
IKEv2 Issue, can\t bring tunnel between Cisco Router and Palo Alto
Hi, I'm getting strange issues when I cannot bring up the tunnel between Cisco Router and Palo Alto FW,On Cisco router side I'm getting this on debug IKEv2:==================================================================*May 10 06:34:55.253: IPSEC:...
Azure AD MFA for Anyconnect VPN clients with ISE 3.0 REST ID
Hi All,Wondering if anyone is using ISE 3.0 REST ID with Azure AD ? https://www.cisco.com/c/en/us/support/docs/security/identity-services-engine/216182-configure-ise-3-0-rest-id-with-azure-act.htmlIf yes, once you've added Azure AD as an External Id...
NAT for ping ICMP from outside to inside via ASAv
Hi, I am 4-year student to university of since from Vietnam. I have a problem about ping ICMP through ASA. I can ping from R2 from outside to 4.0.0.1 of DMZ or 8.0.0.1 of inside. I can ping from DMZ via inside. Can also ping from DMZ and inside to go...
cisco macsec between my head office and branch offices
cisco 9500 layer 3 switch in the head office and C3560CX switches in 5 branch offices. ISP gives an interface to the head office, both data vlan and internet vlan. I want to establish macsec between the branches.can anyone support me in macsec setup?
How to get to know Cisco FTD 2130 throughput
Hello all, I would like to know how to calculate current throughput value at FTD 2130. What sort of information need to calculate it.? Thanks for any response to solve it.
While browsing it can't connect ESA with domain name
Hi,When i try to browse ESA with domain name it is not get connected. But when i put ip address then the ESA login page appeared and we can login. what can be the issue?
Cisco anyconnect browser ERR_SSL_Protocol_ERROR
Good day to everyone.I have two Cisco ASA running on FPR2130 assembled into a balancing group, for example:vpn-gw1.example.comvpn-gw2.example.comgeneral address vpn.example.com.Firmware version 9.18.3.56Anyconnect 4.10.07062At the moment, all our emp...
Resolved! FirePower 1100 lost smart registration
I have a FirePower 1100 for my home lab and for some reason, it lost DNS connectivity and lost registration. I did not notice and now I can't deploy changes. I connected to the CLI and tried to ping from system. When I try to ping from system I get t...
Updated to Ubuntu 24.04. I am not able to use Secure-VPN anymore
Hi, as the title says, I am unable to connect to my Cisco Secure VPN after updating my OS from Ubuntu 22.02 to 24.04. The error I receive is"You are missing the required libraries for the authentication method you requested."Upon closer inspection, t...
Cerificate not valid yet
HiSo basically I have this problem I have eve ng VM and inside of it I'm installing ise primary node and secondary node and AD so I configured a NAT pool on the router and I control those equipements with internet addresses, so now I make a MGMT PC a...
DHCP Server issues DOT1X
HelloAfter I have setted every policy on the switch and everything is working fine through an ISE authentification via dot1x, now server cannot reach its gateway in order to give IP DHCP addresses to the hosts on VLANs!Can anyone help me please
Resolved! FTD Routing question
Hi to all,i am facing the following problem, please refer also to the png attached (i also have some information on the png attached).An IPsec VPN 2811 router tries to establish an IPSec vpn with an FTD. I have setup this config on the lab and i noti...
Allowing access through ISR-C1111 to FPR1010
HelloSo I configured my RA configuration on my FPR1010 for access to my LAN 192.168.5.0/24 but was curious how exactly would I allow this on my ISR to let me connect to it? Not exactly sure which Ports would be needed opened
IPsec tunnel using private ip
Hi All, Can we create an ipsec tunnel between umbrella data center and Cisco FTD firewall using private ip ?. In my infrastructure isp is terminated on router and FTD is behind Router.
| User | Helpful Count |
|---|---|
| 60 | |
| 56 | |
| 53 | |
| 31 | |
| 29 |
