Cisco Catalyst Center
This community is for technical, feature, configuration and deployment questions. For production dep...
2155 PostsActivity in Networking
Cisco 2960S not pinging, but has DHCP address
Hi,I am trying to set up an SSH connection to my switch, but right now there is some lower level problem. I have set up my FastEthernet0 interface to ip address dhcp and the command show interfaces FastEthernet0 shows the correct address. Even if I t...
BOOT FAIL C cisco catalyst 9300
When I start the switch, the text BOOT FAIL C appears in the console and the gear indicator, the system, flashes orange, tell me what to do?
Multiple sub interfaces with Native vlan's?
Sorry, I am reposting because I want the community to see this because where I previously posted, the thread shows resolved already.I have an ASR 10g interface that is connected to a native vlan1 in a HP switching fabric (8 switches) for databases (i...
Resolved! L2TPv3 tunnel between Cisco 2901's
We're trying to form an encrypted IPsec/L2TPv3 tunnel between two 2901 routers running IOS 15.4+. When we try to connect, we can see that the IPsec tunnel is up and that the xconnect session is up but no L2 traffic is traversing the tunnel. We are ...
Resolved! Removing Device Pack file from Prime Infrastructure
Hello.On the Software Update page of Prime there is one Pack which i can not install or delete because it is already included in another installation i did before. Now this pack stays on the page and i am not able to remove it. Does anybody know wher...
CDP Mismatch from CDP: Why?
Switch A, Cisco 9300, VTP mode transparentinterface GigabitEthernet1/0/5switchport access vlan 3switchport mode accessSwitch B, Cisco 3560, VTP mode transparentinterface GigabitEthernet1/0/1switchport access vlan 3switchport mode accessVlan 3 (L2) vl...
ISR 4k Netflow not sending data
I've got 15+ Cisco ISR 4000's (a mix of 4331s and 4551s) in our network and when trying to setup Netflow to PRTG, It seems that when I hit 5 interfaces that need to be monitored, there is always 1 that won't come up in PRTG and that doesn't send data...
IOS not found after factory reset, goes to rommon
Hello,I did a factory reset in my cisco switch 9200L 48 PoE, but after doing that, it seems the switch require to install new OS and there is no copy OS in flash memory. When I try to connect external USB it doesn't respond. What should I do?Here is ...
When will Catalyst 1000 be allowed into Catalyst Center family?
DNA/Catalyst Center is a great tool for surveillance and managing the network. But why cant we connect Catalyst 1000 switches to the Catalyst Center ????????
Unable to Access Web Server - Whats Wrong with this Configuration
ASA working in IPSec, I am able to access HQ from UNIT No problem. Internet is only allowed on specific IPs which are outside DHCP Scope. When I assign IP for internet, now Internet is working, HQ Network is accessible, but S_EXT (webserver - 10.10.1...
Resolved! PBR doesn't work on ASR1001x
Hello everyone!We have ASR1001x with fullview and ipsec tunnels. We use local policy to forward packets from PA addresses to their respective gateways. When the traffic load is high PBR stop working and the router starts using cef, when there is litt...
Cisco Archive config - any changes / Cisco commands
Hello Professionals,I have configured Archive to log config whenever type write memory.I would like to use this auto backup in other way too.Could anyone tell me how to configure followings?1. Is there possible to backup config whenever I make any ch...
NTP and Syslog packets with specific IP Address
Hi All,I have a couple of C9300 L3 switches that are connecting to an ASA firewall. The NTP and the syslog server for the switches are located behind a firewall.When one of the switches request/send packets the gateway IP is the source address on the...
Is there a way to log the MAC connected to a port on a Catalyst?
hi! I am curious as to whether the requirements requested by the customer will be supported by the Catalyst Switch. The requirement is that when the H.H.H PC is connected to the Catalyst Switch port A, a history of the H.H.H MAC connection to the A p...
DNA Center Full Backup Size
Hi, I have a DNAC Server gen 2, configuration with 2 SDA Fabric Site. I managed about 215 Devices (included Fusion Router, Border Switch, Intermediary Switch, Edge Switch, WLC and AP). I doing a full backup but size is so big (~ 213 GB), backup progr...
| User | Helpful Count |
|---|---|
| 70 | |
| 39 | |
| 39 | |
| 35 | |
| 34 |
| User | Count |
|---|---|
| 23 | |
| 17 | |
| 16 | |
| 11 | |
| 10 |
