Hi all I know that upgrade a relase in ISSU mode on WS-C6807-XL-6T device is not advisable.Anyway, My question is: if the upgrade is done inside the same release train could we have problem ? for example:from 15.5(1)SY8 to 15.5.1-SY12orfrom 15.5(1)SY...
how can we determine how much traffic passes through the interface vlan in the Nexus switches,the command (show interface vlan ) doesn't give the needed same as the catalyst,also, (show interface vlan counter) the values we can't read!
Hi everyone, I saw some strange logs today, but I didn't know what they meanFeb 25 10:51:32.493 CNT: %PLATFORM_MATM-4-QUEUE_OVERLIMIT: MATM dropped learn cache batch messages as queue limit has reached.Feb 25 10:52:32.545 CNT: %PLATFORM_MATM-4-QUEUE_...
Hello,I have subnet like this :My pc under vlan 100 (192.168.100.0/24)My NAS under vlan 150 (192.168.150.0/24)Actually when the nas and pc located under same subnet, I can discovery the nas from my laptop using vendor utility, but can't discover when...
I try to generate CSR through GUI - System setting -> System Certificates -> Generate new CSR, but I get error - "The common name does not contain a valid IP address or Domain Name" but maglev cluster network display shows that cluster_hostname the s...
Hey,I have the issue below when I want to upgrade my C9200 from 16.12.3a to golden 17.06.05.Task NameUnpack ImagesTask StatusFailure (NCSW10523: Distribution of image: cat9k_lite_iosxe.17.06.05.SPA.bin on device: 10.4.69.10 with protocol: HTTPS compl...
I have an ISR 1K with DUAL ISPs (Dialer0 & Cellular) My intention was to implement something similar to this article: https://learningnetwork.cisco.com/s/question/0D53i00000Kt1XYCAZ/nat-failover-with-dual-isp-on-a-router-configuration-example?t=17103...
I installed ThousandEyes on my C9407 switch. It seems to be working but I keep getting the following message in the switch logs%IM-5-IOX_INST_NOTICE: R0/0: ioxman: IOX SERVICE teyes LOG: Error posting results to https://data1.agt.thousandeyes.com: HT...
Hi all , with Velocity-Templates there was the possibility to add interactive or exec commands to the template which works fine.Now customer wants to use Jinja2-Template, seems this MODE_ENABLE and INTERACTIVE is not possible there, is there another ...
We have a dilemma on what to choose, strange thing is that currently they confirmed to use SD Access at main offices i.e we will have borders as cn and routers in DC as TC to create VXLAN/LISP sessions over DC between multiple sitesBut if they choose...
HiI'm trying a very simple LAN Automation test where I have one Border manually configured and discovered which I am then going to use as a seed device for my second Border. When I start the LAN automation process the second Border upgraded to my Go...
Hello, since a few weeks, we are notice a lot of timeouts in our network. We figured out that there are unplanned reboots in our stack. This is what the stack is logging: We are using the stack in a ring-topology in hybrid-mode with the firmware 2.5....
Hi,after a upgrade from xe 3.11.07 to 3.11.09 we cannot open a ssh session to our 4510+R Switch. Before the upgrade everything works fine. The error message in the log is:%SSH-3-BAD_PACK_LEN: Bad packet lenghthWe zeroised the rsa key and generate i...
I am sure that I missing something simple in my understanding of how this works. I have connected my virtual CML lab to my network through the external connector. I am able to reach the internet from my edge router. However, for some reason I can not...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: