Hello Team,I'm facing a challenge to apply a patch on the Cisco ISR4331. See the below error message from the router. SIMBA-RT#install add file bootflash:isr4300_cpld_update_v2.0.SPA.bin activate commitinstall_add_activate_commit: START Wed Mar 27 11...
Greeting everyone! There is a little problem with configuring tacacs server on ws-2950-24 model switch. The rest switches we have are 2960 series, also 3xxx series and others, more modern versions. We always configured tacacs server this way:tacacs-s...
Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Friday, March 15, 2024 through Friday, March 29, 2024. Our colleagues Pandian Ponnuswamy, Gautami Sinai Neureker and Sankkar R will be w...
HelloSo I wanna verify if maybe this is normal function or a misconfiguration on ACL or a missing one but a DMZ host is mounting a [Samba Share] from an INSIDE Host, on completely different Network, but NO ACL Permitting it... Any ideas?ISR C1111 ...
Hi All,Looking for snmp configuration for cisco N540x router.I got information in cisco docs.But configuration bit confuse.Can someone please send me actual command to configure snmp in cisco N540x routerThanks,Prashanth
I’m not sure if I’m posting this in the right spot; I’m new to this needing help with setup of a device. I’ve been trying and failing at setting up my 5506. I have a few questions I think if I can get cleared up I can maybe get this working. Please h...
I have Configured the 802.1x Configuration in WS-C2960X-24TS-LL Switch Globally. when i test the aaa test it was successful. but when i tried to configure in the Interface the authentication was not happening. so can you please help to configure the ...
Hi,I set up vlans, interface vlans with IPs, access ports, link aggregations and trunk on my Cisco 3172TQ.I also set up a linux machine as a test machine to check the configuration.If I send tagged traffic to the access ports of the switch, it seems ...
Hello, CML (Cisco Modelling Lab) 2.5 announced a virtual Catalyst 9000 running IOS-XE 17.10 - I tested this out on my personal CML 2.6.1 and I am struggling to get 802.1X working. I know Cat 9K virtual is still a beta release and the CML folks can't ...
1. Make end to end connectivity first. 2. Block the network for these site 1)Make sure that Site 4 will not advirtise any network to Site 5 which it receiving from Site3 routers. 2) On site 5 , when we check routing table of R2 router, it dont ha...
A very good evening to all!There are times when the IOS on a switch may crash and (as a last resort) you need to use the painfully slow Xmodem transfer to save your life. I bought a 3550 a while back and that is precisely what happened with me. Witho...
Hello,I have very simple Cisco EVPN VxLAN fabric running on Cisco nexus 93180YC-EX switches. I am using OSFP + iBGP for underlay/overlay with Multicast. I have border-leaf switches connected to single ISP with eBGP peers and I am advertising my publi...
PI version 3.10 , I configured an SMTP server in "Administration/Settings/System Settings/Mail Server Configuration" and then clicked "Test" but nothing happen,I never received the test mail.PI alarm said:System with IP Address '192.168.99.210' faile...
these routers are direclty connected via point to point connection. When I try summarization, only ip route x.x.x.x x.x.x.x null0 with network statement works for me. When I use the aggregate address command I dont see summary route in route table....
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: