So, previously I had a static IP address I could point putty at that would SSH just fine. I verified the address in a Show Run form I copied two days ago, so I'm not crazy. The config was written to memory multiple times so it's not that.Today, after...
What is the criteria to create SVI and VLANs in the 9800. If you take multiple AP management bands (vlan) to the same network Do I have to need several SVI and/or Vlans?
Team,On this Te0/0/0.667 subinterface we have more than 200 users. so we set the PPPOE maximum session.After setting up PPPOE maximum session to 1000 , IPTV not connecting automatically and getting option SKIP or RETRY. after select skip IPTV getting...
Hi All,I have a couple of C9300 L3 switches that are connecting to an ASA firewall. The NTP and the syslog server for the switches are located behind a firewall.When one of the switches request/send packets the gateway IP is the source address on the...
ASA working in IPSec, I am able to access HQ from UNIT No problem. Internet is only allowed on specific IPs which are outside DHCP Scope. When I assign IP for internet, now Internet is working, HQ Network is accessible, but S_EXT (webserver - 10.10.1...
I configured NAT and DHCP relay in GNS3, and all hosts have end-to-end reachability, I can ping PC44 from PC11 and PC22, and also from PC33 if I configure a static IP address.On the NAT router (R11), I also configured DHCP relay with 'helper-address'...
Hello,I have a cisco router connected to ISP using Dialer interface. I can access the web no problem, but have problems configuring port forwarding to a local computer from outside. Trying with tcp port 5555.Any idea what I am doing wrong? Thanksvers...
Hi,I have been testing MST in my lab which has 3x Cisco Catalyst WS-C2960CG-8TC-L switches.I configured only MST and LACP on each switch and connected them in the ring topology. Test is to see how much time it takes for convergence in such conditions...
hi guys thanks for your suggestions in advancei just reconsidered my whole message. after trying some things. i think i need to set up acl but i'm far from good at it.what would be the ip access-list extended or access-list lines that'd allow me to h...
Is there anyone here using Cisco 8000 series (8801/8802/etc) in their backbone with VXLAN? I’d like to get some feedback of this Silicone One based platform.Use case: Looking for a backbone upgrade from Cat6K based VPLS to something new. Have 6 pairs...
My router not getting IP Address after reload. Interface IP-Address OK? Method Status ProtocolGigabitEthernet0/0/0 192.168.231.9 YES NVRAM up up---GigabitEthernet0/0/1 unassigned YES DHCP up up--- Gig 0/0/1 Connected to ISP Router, since we not gett...
I've got 15+ Cisco ISR 4000's (a mix of 4331s and 4551s) in our network and when trying to setup Netflow to PRTG, It seems that when I hit 5 interfaces that need to be monitored, there is always 1 that won't come up in PRTG and that doesn't send data...
Hello,Pleased help me! I have configured macro auto execute on Switch C3560E as below but it does not work, The idea is that when a link change to up, the switch automatically assigns this link to VLAN 10, and then link down, switch removes this link...
We found N7K-C7010 line card module 3 reload and found logging as below. 2024 Apr 26 13:08:19 SNIPER-01 %SYSMGR-SLOT3-2-SERVICE_CRASHED: Service "nfp" (PID 1130) hasn't caught signal 11 (core will be saved).2024 Apr 26 13:08:20 SNIPER-01 %NFP-SLOT3...