Cisco Catalyst Center
This community is for technical, feature, configuration and deployment questions. For production dep...
2147 PostsActivity in Networking
Failover according to Meraki MX WAN LOSS threshold
Hello. We're currently running Meraki, and there is an issue we found. As far as I know, MX failover is automatically activated when the WAN is disconnected. If WAN Loss reaches a certain threshold, can't you force failover to Unit 2? Thank you.
Serial Interface Configuration Help with C8300
Hello I am currently having trouble translating a configuration on a serial interface from a C3900-SPE150 to a C8300-1N1S-6TThe current configuration on the C3900 on the serial interface is as follows:ip address X.X.X.X 255.255.255.252encapsulation...
Extended ACL inbound and outbound
Good morning friends,I have created two extended ACLs for in and out of my int vlan and applied it under int vlan for both directions inbound and outbound. I have created ACLs entries like this.For int vlan no. Out1 permit ip 10.1.0.0 0.0.255.255 hos...
Simple nat config refuses to work on Cisco ASR 1001 ???
I have simple nat config which I need to use:ip nat pool test 40.0.0.3 40.0.0.3 netmask 255.255.255.0ip nat inside source list 1 interface GigabitEthernet0/0/1 overloadip nat inside source list 2 pool test overloadaccess-list 1 permit 10.0.0.0 0.0.25...
Configure Port-channel and vPC in advance in Nexus 9K
hi,i'll be configuring a new N9K switch to replace a C9300.my question is, can i configure in advance the port-channel and vPC in the N9K even without the SFP inserted and fiber cables patched?just want to prepare the config so it will be a faster to...
Mounting catalyst switch port direction to the hot corridor. Ok or not
1Gb catalyst switches has air intake from front and side and exhaust to the back. And no versions with reverse-airflow.I know many places where such switches installed port side to the hot corridor - so it intake hot air and blow to direction of col...
odd loopback errdisable issue
My company has 4 Call Manager subscribers, two at our HQ datacenter and two at our colocation. We powered down everything at our colo this part Saturday because we are moving it out of state. Since then, we have had random locations having switch ...
Configuring NAT overload with vrf lite on a CAT9K
Good day;Need help with how I can configure NAT overload with an existing vrf on a CAT9K_IOSXE V16.12. This is what I am struggling with, I currently have a vrf called AWSDX-S3. Now what I am trying to do is I have added a L2 SW and ran trunk ports...
Cisco SDA Border to Fusion Connectivity
Do all VNs from a SDA border node need to the same fusion device? We would like to take our Corporate traffic and fuse that to our GRT with a Nexus switch. We'd like to take our IOT and Guest VNs and run them through a firewall for policy and inspe...
Resolved! Dual ISP connection gi0/2 not able to connect to internet
Hello,I need your help - currently we have a 2921 Cisco router connected to dual ISPs using "gi0/0 & gi0/1" and we are able to connect to either ISP successfully. Once we connect gi0/2 to any device the connected switch is not able to access the in...
Resolved! Stop in progress template provisioning
Hello everyone. I'm very new to DNAC or Catalyst Center. I've setup a project with a template to add a simple configuration to switches. It currently has been in progress for 10 days and hasn't made a change to a switch yet. I'd like to cancel th...
IP routing using domain
The host for my current server (Windows Hyper-V machine with four or five VMs) that handles my email and web sites is going away. I'm planning on moving that physical server to my house and using DDNS to route that traffic in. Realize this is very lo...
CTF: my first post
Hi ! Thanks for setting this CTF! It is a great way to learn. bye
First Post for CTF event
This is my requisite first post. CTF has been pretty helpful thus far...
Help with routing vlans
Can someone tell me how do I do routing here ? it does not matter if it is static or dynamic I just want to ping same vlans and also I dont want to have different vlans to be pinged
| User | Helpful Count |
|---|---|
| 65 | |
| 39 | |
| 37 | |
| 36 | |
| 35 |
| User | Count |
|---|---|
| 24 | |
| 16 | |
| 16 | |
| 12 | |
| 11 |
