Packets received by the router from BGP enter via a serial interface at 209.165.201.10. Each route is present within the routing table. Which interface is used to forward traffic with a destination IP of 10.10 10 24?People are saying that the answer ...
Hello, I was creating 2 decently large ACL's to match some traffic today and I noticed something peculiar that has me puzzled. My first ACL has approx 90 ace's and pastes them fine. When I go back and look at the ACL, it looks like there are only lik...
hii have cisco 6500 series core switch and facing a bizarre issue with data speed transfer.I have two vlans svi for which is defined on this switch (core6500). these vlans are transported to another switch (sw5) via lacp etherchannel which is providi...
Hello, I built using the packet tracer a simple topology of three routers with ospf routing. I created a tunnel between the two routers that are not physically connected to each other, but I can't ping between one end and the other. I managed to ping...
DNAC Installed Version: 2.3.5.5-70026Cisco Catalyst 9800-80 17.9.4aAXE 9120i, 9130We have about 10 employees in our office using DNAC at varying role assignment levels.I am Super-Administrator and handle most of the the WIFI related tasks. Of all the...
I configured the simple network below to test the connectivity of the ipv6 in the devices. The configurations are as shown and ipv6 unicast-routing is enabled. When pinging from Router 5 to Router 6 G0/1, it succeeds but when pinging from Router 5 to...
Good day;Need help with how I can configure NAT overload with an existing vrf on a CAT9K_IOSXE V16.12. This is what I am struggling with, I currently have a vrf called AWSDX-S3. Now what I am trying to do is I have added a L2 SW and ran trunk ports...
Greetings,I have a Catalyst 3650 (IOS-XE 16.9.4) that is sending a ton of unsolicited messages to the console. These don't look like Syslog messages. Can anyone tell me how to get this to stop? The switch has been cleared (del vlan.dat, wri era, relo...
Good morning all!I am working on a project on our SD-WAN. I am new to SDWAN and vManage and was asked to look into possibly scripting some packet captures over a period of time. Our SDWAN consists of several IR1101's and they can only be managed via ...
Hi. I was wondering if you could help me with a query I have regarding the new version of DNA 2.3.3.5. And it is that, since I updated to this new version in a DNA in production, in the inventory part it shows me a new column of "EoX Status” If I pu...
Hello, Je désire resetter le mot de passe d'un Switch Cisco Cisco N3K(C-31108TC-V). Je n'Ai pas accès au CLI via ssh ou console port. Merci pour vos retours
Hi,I have a problem with stacking two cisco 9200L's, after stacking, one of the pair goes straight to privileged exec mode, without enable password, while the other needs password for it. It's not the first time, this occurs, do you have any idea whe...
NOTE: I have done the same test setup with 4000 series routers, and routing works fine.I have successfully setup 3 SVI (Static Virtual Interface) tunnels with IPSEC between 2 9300X switches.- I can ping the tunnel IPs- I can ping each VLAN interface ...
In my environment we have multiple cEdge devices, 1 vManage, 2 vBond and 2 vSmart.Due to some reasons one of the cEdge devices lost connectivity to vMange. Not sure of the exact reason.But would like to understand, will there be any impact due to thi...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: