When registering devices on the Smart Account for licencing, how do you license all members in a stackwise-virtual stack? I have two C9500-24Y4C devices currently in my network, they are connected in a stackwise-virtual link. I have registered the ma...
Hello,I have subnet like this :My pc under vlan 100 (192.168.100.0/24)My NAS under vlan 150 (192.168.150.0/24)Actually when the nas and pc located under same subnet, I can discovery the nas from my laptop using vendor utility, but can't discover when...
I have an ISR 1K with DUAL ISPs (Dialer0 & Cellular) My intention was to implement something similar to this article: https://learningnetwork.cisco.com/s/question/0D53i00000Kt1XYCAZ/nat-failover-with-dual-isp-on-a-router-configuration-example?t=17103...
Hi,after a upgrade from xe 3.11.07 to 3.11.09 we cannot open a ssh session to our 4510+R Switch. Before the upgrade everything works fine. The error message in the log is:%SSH-3-BAD_PACK_LEN: Bad packet lenghthWe zeroised the rsa key and generate i...
Hello, everyone. Our compnay is going to upgrade C9200 software. Can we directly upgrade C9200-48P from 17.03.03 to 17.09.04? 您好,最近相对公司的 C9200 交换机进行软件升级,目前交换机的软件版本是 17.03.03,可以直接升级到最新版本 17.09.04 吗?有没有需要注意的地方?
Dear friends,We are planning to deploy new SD-Access and SD-WAN infrastructure, but I had a few questions:Is it possible to connect remote branch SD-access equipment (DNA access switches) behind SD-WAN router? I mean to see it in Fabric, configure vi...
Hi guys, today I have a little problem with SDA-transit and I am not sure, if I am doing it wrong or DNAC (or CC). I have a customer and we want to migrate to a SDA fabric solution. The customer has different remote locations where we can use higher ...
i try to install it on kali but this error still exist The following packages have unmet dependencies: packettracer: Depends: libgl1-mesa-glx but it is not installable
Hello, since november 2023, when our cisco prime 3.10.4 trying to get the config via ssh from our 4510+R Switch, the privilege level 15 changed to 1 and the ssh connection fails. Bevor the config was archived correctily. This problem only occours wit...
Hello,I have topology like this picture where we have 2 WAN connection to bridge LAN1 and LAN2. We use OSFP for the routing and we have NPM (from solarwinds) to monitor WAN connection from LAN1.In the NPM i create 2 node with ip 10.100.1.2 and 10.101...
Hi,Is it possible to configure an MPLS VRF without the use of RDs? I have tried to get this to work in a lab but have been unsuccessful (I have always had to use RD to get it to work)If I were to set up a MPLS VPN between a Nexus switch which has VR...
Hello, I was trying to construct a simple network and got it up the specifications, however when the last step was to configure ipv4 static routes I couldn't quite get it to connect and ping end to end. I tried multiple things but nothing seemed to w...
Hello there.I am trying to upgrade my Switches in installmode to a higher version but it fails, because of invalid image. Switches to upgrade:1x WS-C3850-48P // 2x WS-C3650-48PD IOS in use:16.12.10 CAT3K_CAA-UNIVERSALK9IOS to upgrade to:16.12.10a CAT...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: