Hello,I have topology like this picture where we have 2 WAN connection to bridge LAN1 and LAN2. We use OSFP for the routing and we have NPM (from solarwinds) to monitor WAN connection from LAN1.In the NPM i create 2 node with ip 10.100.1.2 and 10.101...
When registering devices on the Smart Account for licencing, how do you license all members in a stackwise-virtual stack? I have two C9500-24Y4C devices currently in my network, they are connected in a stackwise-virtual link. I have registered the ma...
Hello there.I am trying to upgrade my Switches in installmode to a higher version but it fails, because of invalid image. Switches to upgrade:1x WS-C3850-48P // 2x WS-C3650-48PD IOS in use:16.12.10 CAT3K_CAA-UNIVERSALK9IOS to upgrade to:16.12.10a CAT...
Hello,i'm trying to upgrade my two switch stack from 17.09.04a to 17.09.5. While typing "install add file bootflash:cat9k_iosxe.17.09.05.SPA.bin" i get the following: install_add: START Mon Mar 11 13:22:49 UTC 2024install_add: Adding IMG--- Starting ...
Dears, OSPF diagram show as belowR1 (Area 12 ) ---- R2( Area 0) ---- R3 (Area 0)---- R4(Area 10)if only R1 loopback 0 interface advertised to R3 and only ABR router summurize to Area 10 , how to configure Best Regards,
I have an ISR 1K with DUAL ISPs (Dialer0 & Cellular) My intention was to implement something similar to this article: https://learningnetwork.cisco.com/s/question/0D53i00000Kt1XYCAZ/nat-failover-with-dual-isp-on-a-router-configuration-example?t=17103...
Hi I wanted to enable my ISR Firewall in addition to my FPR Firewall and wanted to check and verify this would be safely implemented and didn’t miss anything.My main interest aside from blocking everything I don’t want in was to allow each network In...
Hey,I have the issue below when I want to upgrade my C9200 from 16.12.3a to golden 17.06.05.Task NameUnpack ImagesTask StatusFailure (NCSW10523: Distribution of image: cat9k_lite_iosxe.17.06.05.SPA.bin on device: 10.4.69.10 with protocol: HTTPS compl...
I have a less then a dozen Cisco 3850 switches that I am working on. I need to configure 802.1x authentication. The issue is the switches are reaching out to Cisco ACS and I need to set up radius server to enable 802.1x. The Cisco ACS I found out ...
I have 2 IE-4010-4S24P on my bench that when I run a diagnostic start test all I get a failure on TestPortAsicLoopback, after a reload the failure still exists. Does anyone know what could cause this, or is this likely a hardware issue?2) TestPortAsi...
In a NX-OS VPC environment with SVI on the Distribution Switches it's not possible to get a DHCP Client DISCOVER (L2 Broadcast / L3 Broadcast) through the SVI nodes. According to Differences between DHCP relay on the Nexus7000/NXOS and IP Helper on ...
Hello, hoping someone here can help me out.This is post emergency-install to ios version 16.12.10.a the switch fails to fully boot, I have also tried emergency install to 3.7.5E with the same result.Below is the switch bootup output , the contents o...
Hallo zusammen,Ich denke, normalerweise ist eine BFD-Sitzung 1 zu 1, wie unten, oder?Schnittstelle Vlan100IP-Adresse 10.1.1.1 255.255.255.252bfd-Intervall 100 min_rx 100 Multiplikator 5Wenn ich jedoch eine sekundäre IP-Adresse verwenden möchte, ist e...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: