Hi,we are facinf and issue with ping from access to corecore management vlan 98 192.168.98.1 255.255.255.0vlan 103 192.168.103.1 255.255.255.0trunk port enabled for vlan 103able to ping access switchAccess switch management vlan 192.168.103.137 255.2...
We have ASK 9001 Is this NAT configuration available if not what is the alternate configuration? we are trying to setup a PPPOE configuration in ASR9001 and configured DHCP pool, BBA . how to add nat inside and outside configuration for the authentic...
1. Make end to end connectivity first. 2. Block the network for these site 1)Make sure that Site 4 will not advirtise any network to Site 5 which it receiving from Site3 routers. 2) On site 5 , when we check routing table of R2 router, it dont ha...
Assume I have to routing among different block of campus network with a square cross connected with OSPF peer to peer type,what is the disadvantage of this square cross design?Is ACI fabric used to replace this square cross design? or replace campus ...
Hey, i am working on a project And I have problems with my DHCP server. I don't remember how it came about. Hence I am asking here. I don't understand why my laptops at the bottom are not getting ip? Anyone who can help me. Packet tracer + Network di...
Assume that there are three router type devices outside firewall, and one core switch router behind one layer firewalland I would like to hide the router hop of core switch router from traceroute how to modify TTL to less values at router at the most...
hi all,we have a topology without any redundant link. Every access switch is directly connected with the core switch, and it's a port-channel between access switch and the core. RSTP runs on switches by default, and we do not explicitly configure the...
Hello all,20+ years ago I used debug all the time, however not so much so in the last decade. Seems like last time I called TAC on the 3850 debug command they gave me some silly answer that debug was a Cisco TAC command. WFIW All the Cisco.com debug...
Hello Team,Can we configure this 1100 series SD WAN Router as normal DMVPN router? C1121X-8PLTEPWe have this requirement as Temporarily. We are observing that we can't run or create crypto policy on this router.is this possible in reality?
Hi, Do you have been happen this logging show that, and there are none any effect to our netwoek bunisness. im client 'chasfs' has taken 332 msec (runtime: 332 msec) to process a 'stack chasfs fd' messageMar 28 23:25:32.568: %IOSXE_INFRA-6-PROCPATH_C...
Hi, im having issues pining between devices, i also cannot figure out how to connect the D1 switch and R1 router. Password for secret is class and normal password is cisco. Would appreciate any help or guidance! thank you !!
I configured cisco dna to send emails as soon as aUser Defined Issue Notification is triggered, configured SMTP, performed the sending test and got the email as expected.But all SYSLOG events that were configured with the subscription for email do no...
First I'll state i also have an open case with Vmware. I inherited a vPC pair that had a number of vPC set up, but the multiple links to the VxRail host nodes were trunk links. We lost the secondary so only the trunks to the primary vPC were up. A...
We are looking at a large rollout of Cisco C8200 1RU w/ 1 NIM slot and 4 x 1-Gigabit Ethernet WAN ports. We need three operational copper 1G ports. I can not find any recommendation on support for copper 1G (GLC-TE=) for this product. Can someone ...
Hello, I can't manage to give the connected PCs an ip through the dhcp server. My packet tracer + network design are attached. Have currently only started on the bottom part so it's only about the bottom PCs.Thanks in advance for the effort
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: