Hello,As per the below diagram I have two switches S1 & S2. Hosts H1 & H2 are connected to the switches and are in different vlan but same subnet. So, by default they will not communicate as they are in two different broadcast domain.To make them com...
The VLANIF of the core switch acts as the gateway for client. The Client is unable to obtain the gateway IP, but by manually adding ARP, it can communicate with the gateway. The core switch has the correct MAC and ARP information for the client, a...
Hi, we have a WAN and VSAT connection to one of the site. WAN is primary and VSAT is secondary link.We have dedicated router for WAN and VSAT. VSAT link is connected to one of the LAN access switch.Could you please help me, what kind of configuration...
I'm trying to create a DNS test that will check for a change in a record. I've created the test with the desired URL and created an alert if the mapping doesn't match x.x.x.x. No alert is ever generated.Is it possible to create an alert for when a DN...
Greetings!So I was practicing to configure VTP and VLANs. For a start, I created 3 switches (only 2 being turned on). The trunks are working fine as the switches are able to acquire an IP addresses via dhcp from a dedicated router and vtp appears to ...
What have I tried?Once I connected the console cable to the router and my system, I checked that the USB port was available in my system and accessible.$ ls -l /dev/*USB* /dev/ttyUSB0 $ dmesg ... [22726.984409] usb 3-3: new full-speed USB device n...
I have created a small network in packet tracer. See attached file. Ignore AS 300 and ISP as they are not configured. I am trying to communicate between AS 100 and 200. When I use show commands everything seems great. I see all routes distributed as ...
Greetings,I'm checking the "show bgp x.x.x.x" output in 3 different XR routers A, B & C in an ISP environment.Here's an example as the best path part of the output:Path #1: Received by speaker 0 Advertised IPv4 Unicast paths to peers (in unique updat...
Hello all, I am trying to automate our own Compliance checks with Ansible using Cisco API.Is there any way to search for devices which are not assigned to a Site? The "Site" Param is not visible in SDK Method "devices.Devices.get_device_by_id, device...
Hi Community, Iam creating Smart license in IOSXR with http So I used "destination transport-method http" and also put the destination url. When I do show run, i see "destination transport-method email disable" also in the configuration ----- call-ho...
hello. I understand that Connected routing has an AD value of 0. The IP bands on the 1st and 2nd floors are different. 1st floor: 1.1.1.0/242nd floor: 2.2.2.0/24 There are two firewalls on top of the backbone. The band will be 3.3.3.0/24. If you conf...
Hi All,We have a URL which resolves to particular public ip and performance of that website is slow than expected from our office . We have a P2P link from office to DataCentre and from DataCentre it exits to internet. We observed the performance was...
Hi All,Quick question hopefully. I noticed that when DNA Center provisions a L2 network within a fabric site, its allocates a L2VNID starting 8188 for local segments and 16196 for multisite remote border/anchor VN segments.If I remove and re-add an p...
When i discover a new switch with LAN-automation other switches, which are not directly connected to the specified interface are going into a queued status. Which means:Queued: The device is queued for later processing because it isn’t directly conne...
Hi all I'm setting up a CISCO LAB to keep me busy in my retirement. My Current network consists of a TP-Link Deco mesh network which works well for my IOT, PCs and internet access. I just got hold of a Cisco 1941 router with a EHWIC D8SGP module. ...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: