Cisco Catalyst Center
This community is for technical, feature, configuration and deployment questions. For production dep...
2136 PostsActivity in Networking
QOS for a Destination-ip in Cisco IOSXE
Hi All,We have a URL which resolves to particular public ip and performance of that website is slow than expected from our office . We have a P2P link from office to DataCentre and from DataCentre it exits to internet. We observed the performance was...
vlan interface administratively down
I just created a vlan, assigned it to a port on our 6509, assigned the vlan an ip address and when i shoot the command, show int vlan 31 it says that the vlan is administratively down. I can't figure out whats going on here? i issued a no shut, to no...
Cisco2960X IBNS 2.0 and 802.1x/MAB Authentication NOT working
Hello,i was successfully deploying Nac configuration on all my switches when i encountered i problem with the new authentication display config-mode on a WS-C2960X-48LPS-L 15.2(7)E4:SwitchplanA#authentication display config-modeCurrent configuration...
IP SLA Monitoring MIB
I've setup an icmp-echo IP SLA on a Cisco C9300 to ping another device on our network. I'm now trying to monitor the amount of timeouts seen by the IP SLA job in our monitoring tool (WhatsUp Gold) but when setting up the monitor, the issue I'm having...
Unable to get console access on switch 3850 - Blank terminal
Hello,I have a switch I am unable get a prompt on the console port.I can SSH to it, and have confirmed that the baud rate and stop bits are correct from the console switch. There are two other switches that I can console to.The differences are that t...
Please explain those terms. I can't understand. Help needed!
"Distribution Switch for Formation" & "Enterprise and Active Directory (AD) Zone Switch"
Simple SSH Connection 9400 Not Working
Is there something different about configuring SSH on a 9407 with a C9400-SUP-1? Currently there's no configuration on the device except for an IP address on the management port and ssh. I've gone through the same procedures we've always used and v...
Need some assistance with some basic VLAN/Routing config Cisco 1941.
Hi all I'm setting up a CISCO LAB to keep me busy in my retirement. My Current network consists of a TP-Link Deco mesh network which works well for my IOT, PCs and internet access. I just got hold of a Cisco 1941 router with a EHWIC D8SGP module. ...
Catalyst 1000 / secureing management access
Hello,I am still considering wheter to deploy Catalyst1000 or CBS350 switch at our small office(15-25 devices).Switch have to be configured with multiple SVIs and DHCP server pools for each + few static routes.I would like to secure MGMT access to th...
DMVPN Spoke not connecting when using starlink
I have set up as above. I am using starlink at one of my spokes. I am not able to get to pass VPN traffic even though show dmvpn shows that the vpn is up.
Migrating Cisco IOS Config to Nexus
I know that there was a tool a couple of years ago which migrated config from Cisco IOS to Nexus but it doesn't look like this is available anymore. Is there anything else around which can migrate the configuration? Python script or similar? https://...
Redundancy Over VSAT Link
Hi, we have a WAN and VSAT connection to one of the site. WAN is primary and VSAT is secondary link.We have dedicated router for WAN and VSAT. VSAT link is connected to one of the LAN access switch.Could you please help me, what kind of configuration...
SSID not discoverable by laptop in Packet Tracer
We have configured two Lightweight Access Points using a 3504 WLC. Both access points are connected to the WLC, and have been assigned IP addresses through DHCP from the WLC. Both also state they are providing the WLAN we created. Authentication for ...
4506 dhcp issue
we had a daily-basis ip conflict with dhcp server on cisco switch 4506E specially after replacing some the users' ports or a user using the laptop and moves alot, the ip conflict is detected using GARP method.note: the user could try multible free IP...
Migrate subnet into SD Access
HiI am testing migrating a subnet into SD Access. I have a subnet routed outside my fabric and I have a device inside my fabric on that subnet routed by the external gateway by handing off the address pool on a L2 VN. This all works fine.I now want...
| User | Helpful Count |
|---|---|
| 59 | |
| 41 | |
| 38 | |
| 37 | |
| 34 |
| User | Count |
|---|---|
| 32 | |
| 17 | |
| 14 | |
| 13 | |
| 10 |
