E1 WIC for Unframed

Unanswered Question
Feb 7th, 2007

Hi,

My E1 controller card is not supporting unframed E1 connection.My E1 card details are below mentioned.

E1 0/0 is down.

Applique type is Channelized E1 - balanced

Description: WAN INTERFACE

Far End Block Errors Detected

Receiver has loss of signal.

alarm-trigger is not set

Version info Firmware: 20040108, FPGA: 11

Framing is CRC4, Line Code is HDB3, Clock Source is Line.

CRC Threshold is 320. Reported from firmware is 0.

Data in current interval (873 seconds elapsed):

0 Line Code Violations, 0 Path Code Violations

0 Slip Secs, 873 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 873 Unavail Secs

Data in Interval 1:

0 Line Code Violations, 0 Path Code Violations

0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs

Data in Interval 2:

0 Line Code Violations, 0 Path Code Violations

0 Slip Secs, 900 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs

Data in Interval 3:

0 Line Code Violations, 0 Path Code Violations

I have this problem too.
0 votes
  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
spremkumar Wed, 02/07/2007 - 01:21

Hi Murthy

Can you confirm whether you have tried configuring channel-group 1 unframed under controller config ?

regds

spremkumar Wed, 02/07/2007 - 02:04

Hi

Can you paste the output of show version and show diag here ?

regds

kvnmurthy Thu, 02/08/2007 - 21:28

Hi,

Sorry for the delay, here is the sh diag command output

show diag

Slot 0:

C2610XM 1FE Mainboard Port adapter, 2 ports

Port adapter is analyzed

Port adapter insertion time unknown

EEPROM contents at hardware discovery:

Hardware Revision : 3.1

PCB Serial Number : FOC08290FRH (433153135)

Part Number : 73-7677-05

RMA History : 00

RMA Number : 0-0-0-0

Board Revision : A0

Deviation Number : 0-0

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 03 6A 41 03 01 C1 17 46 4F 43 30 38 32

0x10: 39 30 46 52 48 20 28 34 33 33 31 35 33 31 33 35

0x20: 29 82 49 1D FD 05 04 00 81 00 00 00 00 42 41 30

0x30: 80 00 00 00 00 FF FF FF FF FF FF FF FF FF FF FF

0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

--More-- WIC Slot 0:

E1 (1 port) WAN daughter card

Hardware revision 1.0 Board revision F0

Serial number 32594159 Part number 800-04475-03

Test history 0x0 RMA number 00-00-00

Connector type PCI

EEPROM format version 1

EEPROM contents (hex):

0x20: 01 21 01 00 01 F1 58 EF 50 11 7B 03 00 00 00 00

0x30: 78 00 00 00 04 08 22 00 FF FF FF FF FF FF FF FF

Router#

kvnmurthy Thu, 02/08/2007 - 21:30

Router#sh ver

Cisco Internetwork Operating System Software

IOS (tm) C2600 Software (C2600-IPBASE-M), Version 12.3(6c), RELEASE SOFTWARE (fc1)

Copyright (c) 1986-2004 by cisco Systems, Inc.

Compiled Tue 20-Jul-04 05:24 by kellythw

Image text-base: 0x80008098, data-base: 0x80ED06CC

ROM: System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)

Router uptime is 7 minutes

System returned to ROM by power-on

System image file is "flash:c2600-ipbase-mz.123-6c.bin"

cisco 2610XM (MPC860P) processor (revision 0x301) with 126976K/4096K bytes of memory.

Processor board ID FOC08290FRH (433153135)

M860 processor: part number 5, mask 2

Channelized E1, Version 1.0.

Bridging software.

X.25 software, Version 3.0.0.

Primary Rate ISDN software, Version 1.1.

1 FastEthernet/IEEE 802.3 interface(s)

1 Channelized E1/PRI port(s)

--More-- 32K bytes of non-volatile configuration memory.

32768K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

Router#

rdessert Fri, 02/09/2007 - 06:36

To configure it for unframed try this:

conf t

controller e1 0/0

no framing crc4

Hope this helps.

handoko.wiyanto Fri, 02/09/2007 - 09:38

hi there,

as my understanding, you are trying to configure E1 as unframed, means for data, correct?

afaik, your e1 card must support g703 for unframed.

what e1 card are you using now?

Actions

This Discussion