Redistributing OSPF thru E-BGP Problem

Unanswered Question
Feb 22nd, 2007

Have a problem, Have a mesh network,

Device A and Device B connect into Cisco 7609 to route to other devices on the network.

Until recently, they all used E-BGP , and traffic was routed:

Device A => Cisco => Network

Device B => Cisco => Network

Device A and Device B have fibre connection.

This was correct.

We changed Device B from E-BGP to OSPF, and REDISTRIBUTEd on Cisco onto network.

Now Device A routes all traffic thru Device B to Cisco !!!

Device A=> Device B => Cisco => Network

Device B => Cisco => Network

Think there is something wrong with Distributive Metric , but am restricted as Device A and B do not have as expansive command set as Cisco 7600...

Any Ideas ??

I have this problem too.
0 votes
  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
purohit_810 Thu, 02/22/2007 - 10:29

Hi,

Can you give previous setup digram and changed setup diaagram and Configuration. Previous and you changed both.

See, as of your talk only we can conclude.... You were using E-BGP (i.e EGP) and Now You are using OSPF (i.e IGP).

It will not performe between AS as BGP.

Any way tell us smothing more about this.

Regards,

Dharmesh Purohit

crumdub12 Fri, 02/23/2007 - 09:37

Unfortunately, The devices are GUI based, and settings were not changed on Device A, but changed on Device B, E-BGP was switched off , and OSPF was switched on, The OSPF on Cisco is as follows.

Relevant IP addresses are:

Device A => Cisco 192.168.216.93-94/30

Device A => Device B 192.168.216.201-202/30

Device B => Cisco 192.168.216.113-114/30

Hope this helps..

router ospf 1

log-adjacency-changes

network 192.168.55.0 0.0.0.255 area 0

network 192.168.56.0 0.0.0.255 area 0

network 192.168.57.0 0.0.0.255 area 0

network 192.168.58.0 0.0.0.255 area 0

network 192.168.126.0 0.0.0.255 area 0

network 192.168.210.0 0.0.0.255 area 0

network 192.168.211.0 0.0.0.255 area 0

network 192.168.212.0 0.0.0.255 area 0

network 192.168.213.0 0.0.0.255 area 0

network 192.168.214.0 0.0.0.255 area 0

network 192.168.215.0 0.0.0.255 area 0

network 192.168.216.0 0.0.0.255 area 0

network 192.168.217.0 0.0.0.255 area 0

network 192.168.218.0 0.0.0.255 area 0

network 192.168.240.0 0.0.0.255 area 0

maximum-paths 1

router bgp 65534

no bgp default ipv4-unicast

bgp log-neighbor-changes

bgp graceful-restart restart-time 120

bgp graceful-restart stalepath-time 360

bgp graceful-restart

neighbor 10.10.10.2 remote-as 65534

neighbor 10.10.10.2 update-source Loopback0

neighbor 192.168.100.18 remote-as 64512

neighbor 192.168.100.26 remote-as 64512

neighbor 192.168.103.110 remote-as 65103

neighbor 192.168.103.113 remote-as 65103

etc ....

maximum-paths 2

!

address-family ipv4

redistribute connected

redistribute ospf 1

neighbor 10.10.10.2 activate

neighbor 192.168.100.18 activate

neighbor 192.168.100.26 activate

neighbor 192.168.103.110 activate

neighbor 192.168.126.113 activate

neighbor 192.168.126.113 route-map ****_routemap out

neighbor 192.168.127.117 activate

neighbor 192.168.127.121 activate

neighbor 192.168.128.113 activate

neighbor 192.168.131.117 activate

neighbor 192.168.131.121 activate

neighbor 192.168.163.49 activate

neighbor 192.168.163.53 activate

neighbor 192.168.163.61 activate

neighbor 192.168.163.65 activate

neighbor 192.168.163.69 activate

neighbor 192.168.179.9 activate

neighbor 192.168.179.81 activate

neighbor 192.168.200.18 activate

neighbor 192.168.200.26 activate

neighbor 192.168.210.21 activate

neighbor 192.168.210.21 route-map B***_routemap out

neighbor 192.168.210.25 activate

neighbor 192.168.210.25 route-map ****_routemap out

neighbor 192.168.210.45 activate

neighbor 192.168.210.105 activate

neighbor 192.168.210.121 activate

neighbor 192.168.210.141 activate

neighbor 192.168.210.141 route-map ****_routemap out

neighbor 192.168.214.193 activate

neighbor 192.168.214.193 route-map ****_routemap out

neighbor 192.168.214.197 activate

neighbor 192.168.214.197 route-map ****_routemap out

neighbor 192.168.217.14 activate

neighbor 192.168.218.2 activate

neighbor 192.168.218.6 activate

neighbor 192.168.219.49 activate

neighbor 192.168.230.33 activate

neighbor 192.168.230.129 activate

neighbor 192.168.230.161 activate

neighbor 192.168.230.161 advertisement-interval 2

maximum-paths 2

no auto-summary

no synchronization

bgp dampening

network 10.10.10.0

network 190.168.0.0

network 192.168.0.0

network 192.168.100.19 mask 255.255.255.252

network 192.168.200.19 mask 255.255.255.252

network 192.168.200.27 mask 255.255.255.252

exit-address-family

!

Actions

This Discussion