03-13-2007 12:02 PM - edited 03-14-2019 08:28 PM
Hi,
I need to know if anyone has been able to to the following:
- 3 h323 gateways (2800) configured with 2 FXS ports installed
-analog phones connected to the FXS port
-analog phone router1 establishes a call with analog phone router2--> analog phone router 1 presses flash, gets a dial tone from the gateway, calls analog phone router3 and transfers the call.
What is needed to transfer an H323 call from one FXS port to another FXS port on a different gateway?
Many thanks,
Dragi
03-13-2007 12:25 PM
Just a matter of right IOS and configuration. For example, you can configure the FXS ports as SCCP for a central CCME and have all the features:
http://cisco.com/en/US/products/ps6441/products_feature_guide09186a0080483a76.html
Hope this help, if so rate this posts.
03-13-2007 12:27 PM
there is no CCME involved in this. Just h323 with gateways.
Dragi
03-13-2007 12:30 PM
Mine was a configuration suggestion, CCME is embedded in all voice images, and is enable with "telephony-services".
There are ways of having transfer on FXS ports, however that may imply TCL scripting etc:
http://cisco.com/en/US/products/sw/iosswrel/ps5207/products_feature_guide09186a00801814cf.html
The CCME approach is much simpler and better documented.
03-19-2007 06:55 AM
in the end, this is the configuration I used:
tftp-server flash:prompts/en/en_music_xferee_ulaw.au
tftp-server flash:prompts/en/en_author_fail_ulaw.au
tftp-server flash:prompts/en/en_busy_tone_ulaw.au
tftp-server flash:prompts/en/en_dest_blocked_ulaw.au
tftp-server flash:prompts/en/en_dest_busy_ulaw.au
tftp-server flash:prompts/en/en_disconnected_ulaw.au
tftp-server flash:prompts/en/en_enter_dest_ulaw.au
tftp-server flash:prompts/en/en_fast_busy_tone_ulaw.au
tftp-server flash:prompts/en/en_music_xferto_ulaw.au
tftp-server flash:prompts/en/en_no_dest_entered_ulaw.au
tftp-server flash:prompts/en/en_no_service_available_ulaw.au
tftp-server flash:prompts/en/en_operator_is_busy_ulaw.au
tftp-server flash:prompts/en/en_reenter_dest_ulaw.au
tftp-server flash:prompts/en/en_ringback_tone_ulaw.au
!
control-plane
!
!
call application voice transfer_app flash:app-h450-transfer.2.0.0.9.tcl
call application voice transfer_app delay-time 1
call application voice transfer_app language 1 en
call application voice transfer_app set-location en 0 flash:/prompts/en/
!
!
voice-port 1/0/0
!
voice-port 1/0/1
!
voice-port 1/1/0
!
voice-port 1/1/1
!
!
!
!
!
dial-peer voice 1111 pots
application transfer_app
destination-pattern 1111
port 1/0/0
!
dial-peer voice 2222 pots
application transfer_app
destination-pattern 2222
port 1/0/1
!
dial-peer voice 3333 pots
application transfer_app
destination-pattern 3333
port 1/1/0
It works really well. The app-h450-transfer zip file with all the prompts is on CCO, where CME files are.
Dragi
03-19-2007 08:22 AM
Great info, thanks!
I have rated you post 5!
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: