3662 voice gateway connected P2P to ComdialFII via T1 CAS

Unanswered Question
Mar 16th, 2007
User Badges:

Good Day!


We have a client PABX that needs to connect to 3662 voice gateway via T1 CAS


here's the connection details:

T1 CAS Specs:B8ZS /ESF/CAS/DTMF


Call Manager 4.01


3662 config:

controller T1 1/0

framing esf

linecode b8zs

pri-group timeslots 1-24

controller T1 5/1

framing esf

linecode b8zs

ds0-group 0 timeslots 1-24 type e&m-wink-start


dial-peer voice 22 pots

destination-pattern 1715

port 5/1:0


Client PABX is ready to recieve 4 digits extension but i cant get it to work.


Logs on my gateway:

Telephony call-legs: 1

SIP call-legs: 0

H323 call-legs: 1

Total call-legs: 2

381E : 16681440hs.1 +-1 pid:1 Answer 2228 connected

dur 00:00:00 tx:11/1760 rx:0/0

IP 10.21.0.254:21422 rtt:0ms pl:0/0ms lost:0/0/0 delay:0/0/0ms g711ulaw


381E : 16681440hs.2 +-1 pid:23 Originate 1715 connecting

dur 00:00:00 tx:0/0 rx:23/3680

Tele 5/0:2 (1631): tx:470/47/0ms g711ulaw noise:0 acom:0 i/0:-76/-79 dBm



  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 3 (1 ratings)
Loading.
racacjjc08 Sat, 03/17/2007 - 03:45
User Badges:

Diagram:


IPT----VG3662(E&M)----T1CAS(TELCO)----PABX(E&M)

paolo bevilacqua Sat, 03/17/2007 - 04:01
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

By T1CAS(TELCO) do you mean there is a T1 circuit provided by telco?

Have you checked that E&M is on both router and PBX? If your PBX could support PRI, that would things easier.

What is the state of the line ("show controller")?

Please enable debug "debug vpm signal".

racacjjc08 Sat, 03/17/2007 - 04:55
User Badges:

By T1CAS(TELCO) do you mean there is a T1 circuit provided by telco?

Yes, P2P T1 provided by telco


Have you checked that E&M is on both router and PBX? If your PBX could support PRI, that would things easier.


Yes Both is configured as E&M wink start dnis dtmf, I do agree that it would be easier to troubleshoot if we use PRI but the client preferred to use CAS.


What is the state of the line ("show controller")?


T1 is UP( i'l post the state later)

Please enable debug "debug vpm signal".

How would i know the problem?



When i try to dial the 4 digits extension from IP Phone, i got 8 secs delay then fast busy.


We also tried to pull the T1 and connect to sunset t10 tester, dial the 4 digits extension and it is completing and we got our call answered.


based on the setup is it going to work?


VG3662--T1CAS--PABX ???or we need to have a VG3662--T1CAS--VG---PABX ???


Thanks!



paolo bevilacqua Sat, 03/17/2007 - 05:33
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

Hi,

When you enable "term mon" and "debug vpm signal" you will see what the router is doing with the voice signaling, dtmf etc.

There is no need that you place another voice gateway on the other side of the T1, but it would be useful if you could place there circuit analyzer there for diagnostic purposes.

racacjjc08 Sat, 03/17/2007 - 06:57
User Badges:

Thanks!


Any link or documentation you can recommend?


I have tried all the config from E&M to FXS but i still cant make it work. PABX on the other side should recieve a call if i dial 4 digits extension but all i got is busy tone. Where would be the issue?


Thanks for the help!



paolo bevilacqua Sat, 03/17/2007 - 07:45
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

There are many documents on CCO, but since you don't know what the problem could be, this is the generic index:

http://cisco.com/en/US/tech/tk652/tk653/tsd_technology_support_troubleshooting_technotes_list.html


Are you positively sure that the PBX is configured for E&M? Do you have someone on the PBX side that can help checking on things ?


One thing you can try is to call from PBX to router, see which signaling bits are activated, that could help figuring out things.



racacjjc08 Sun, 03/18/2007 - 07:44
User Badges:

Thanks!


I will apply your recommendation tomorrow. We will be having another test of the circuit. I'll keep you posted of the progress.


RA

paolo bevilacqua Sun, 03/18/2007 - 08:30
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

Good luck.


In case of trouble perhaps you can push the PRI configuration to the customer that would allow having this to work in 5 minutes.


Another convincing argument at times is that with PRI they can see who is calling (ANI), as with standard E&M it is not possible.


racacjjc08 Mon, 03/19/2007 - 13:13
User Badges:

Hi,


e&m-delay-dial was used and the call was successfully routed to pabx using 4 digits extension.


Thanks for the responses and help!



Ra

paolo bevilacqua Mon, 03/19/2007 - 13:25
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

All is good what ends good!

If posts are useful, please rate!

Actions

This Discussion