No DHCP on wireless LAN

Unanswered Question
Mar 21st, 2007

Hi guys, I have a Cisco 857W wireless ADSL router and I can get my windows XP w/s to connect but no IP address is assigned. I get a message saying limited or no conenctivity.

Relevant config is:

interface Dot11Radio0

description Wireless LAN

no ip address

no ip redirects

no ip unreachables

no ip proxy-arp

ip nat inside

ip virtual-reassembly

ip route-cache flow

!

encryption vlan 1 key 1 size 128bit xxx transmit-key

encryption vlan 1 mode wep mandatory

!

ssid NOC

vlan 1

authentication open

guest-mode

infrastructure-ssid

!

world-mode dot11d country AU both

speed basic-1.0 basic-2.0 basic-5.5 basic-6.0 basic-9.0 basic-11.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0

channel 2452

station-role root

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

!

interface Dot11Radio0.1

encapsulation dot1Q 1 native

no snmp trap link-status

no cdp enable

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

!

interface Vlan1

description Internal LAN

ip address 10.10.10.1 255.255.255.248

ip access-group 100 in

no ip redirects

no ip unreachables

no ip proxy-arp

ip nat inside

ip virtual-reassembly

ip route-cache flow

ip tcp adjust-mss 1412

Any ideas?

Thanks

Dean

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
prakashj Wed, 03/21/2007 - 10:14

Hi Dean,

You can try with following config

world-mode dot11d country AU both

ssid NOC

speed basic-1.0 basic-2.0 basic-5.5 basic-6.0 basic-9.0 basic-11.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0

channel 2452

station-role root

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

!

interface FastEthernet0.1

encapsulation dot1Q 1 Native

no ip route-cache

bridge-group 1

no bridge-group 1 source-learning

bridge-group 1 spanning-disabled

!

ip dhcp pool LAN

network 10.10.10.0 255.255.255.248

default-router 10.10.10.1

I hope it will help you.

Thankx&Regds

Saji k.s

bporter78 Fri, 04/06/2007 - 09:35

ok you haven't setup your bridge-group 1 properly.

Your DHCP pool is associated with Vlan1 - however your dot11radio0 is associated with Bridge-group 1 and Vlan 1 isn't - therefore you won't get ip's assigned from your DHCP pool.

Do this and you will be sweet:

ip dhcp pool Local

import all

network 10.10.10.0 255.255.255.248

default-router 10.10.10.1

dns-server 10.10.10.1

!

!

bridge irb

!

!

!

!

interface FastEthernet0

!

interface FastEthernet1

!

interface FastEthernet2

!

interface FastEthernet3

!

interface Dot11Radio0

no ip address

!

broadcast-key change 60

!

!

encryption mode ciphers tkip

!

ssid NOC

authentication open

authentication key-management wpa

guest-mode

wpa-psk ascii 0 'enter your keye here'

!

speed basic-1.0 basic-2.0 basic-5.5 basic-6.0 basic-9.0 basic-11.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0

station-role root

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 spanning-disabled

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

!

interface Vlan1

no ip address

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 spanning-disabled

!

!

interface BVI1

ip address 10.10.10.1 255.255.255.248

ip access-group Outbound in

ip nat inside

ip virtual-reassembly

!

bridge 1 protocol ieee

bridge 1 route ip

Actions

This Discussion