Router Forwarding between VLANs

Answered Question
Mar 25th, 2007

Hi,

I'm trying to communicate 2VLAN's in a 2900XL to a 2600Router. My 2600 supports dot1q so I changed the encapsulation and set 2 sub-interfaces on Eth0/0. However, seems there no comm. between 2hosts on the diff. subnets (e/vlan)I've configured both VLANs and set the trunk on Fa0/16 which is part of both VLANs 1 and 3. Any clues on this?

Thank you.

I have this problem too.
0 votes
Correct Answer by mahmoodmkl about 9 years 8 months ago

Hi

Configure the Link between the two swithces as Trunk link.i.e

switchport mode trunk

and see tht u dnot enable portfast on the ports used for trunking.

Thanks

Mahmood

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 4.3 (3 ratings)
Loading.
glen.grant Sun, 03/25/2007 - 08:31

Probably have to post both configs . Also what model is the 2924 ? A old 4 meg or newer 8 meg model . The older ones didn't support trunking i don't believe .

ankbhasi Sun, 03/25/2007 - 09:27

Hi Rodrigo,

Instead of using multi vlan command on siwtch interface can you try this command

interface FastEthernet0/16

switchport trunk encapsulation dot1q

switchport mode trunk

Regards,

Ankur

rodrigo2673 Sun, 03/25/2007 - 10:04

Thanks Ankur! it works now. There is comm. now from host to router.

ankbhasi Sun, 03/25/2007 - 10:21

Hi Rodrigo,

Nice to know that it worked for you.

Regards,

Ankur

*Pls rate all helpfull post

rodrigo2673 Sun, 04/08/2007 - 10:43

Hi,

Im following the same configuration but now I added another sw2926-XL. The problem is: I cannot get to comm. I've connected a crossover between the 2 sw. (Fa0/17) STP is working in FWD mode in both interfaces. However, when I ping the router says Request Time Out. I've also put Fa0/16 which is the host on VLAN 02.

Please, can you help?

Regards,

Rod

Correct Answer
mahmoodmkl Sun, 04/08/2007 - 22:18

Hi

Configure the Link between the two swithces as Trunk link.i.e

switchport mode trunk

and see tht u dnot enable portfast on the ports used for trunking.

Thanks

Mahmood

ankbhasi Sun, 04/08/2007 - 23:42

Hi Rod,

Can you please confirm if you are trying to ping ro touter from the switch? If yes have you det a default gateway on your switch pointing to router ip address?

Regards,

Ankur

rodrigo2673 Sat, 06/30/2007 - 05:09

Hi,

I am trying to comm.3 routers on a hub-and-spoke topology. The HUB router comms.with the "left" router on a point-to-point connection fine. However, the int.S1(multipoint)connected to router "right" does not comm. Please, find attached 3conf.files of each router.

I hope you can see what is missing in my config.

Thanks.

Rod

Attachment: 
rodrigo2673 Sat, 10/06/2007 - 13:25

Hi,

I hope you can help me since I'm having problems configuring my PIX 501. I have set e0 and e1 static ip addresses and they both comm. with their own segments. HOwever, I can't comm. from e1 through e0.

I've set in both NAT (inside) 0 0 0 and outside as well. There are no packet going out from any of both nics.

Please, can you help?

regadrs,

Rod

Actions

This Discussion