E1 access problem in SRST

Unanswered Question
Mar 26th, 2007
User Badges:

Hi,

I upgraded the IOS and the IP Phone are registered, but for outgoing calls not works. I made a call using CSIM command and the call works. The router are connect to PSTN by E1 PRI.Pls. see the SRST config:


call-manager-fallback

max-conferences 8 gain -6

transfer-system full-consult

ip source-address <IP CCM> port 2000

max-ephones 96

max-dn 120

access-code pri 9 direct-inward-dial

time-zone 11

date-format dd-mm-yy


This is the dial-peer for outgoing calls:


dial-peer voice 100 pots

destination-pattern 9

direct-inward-dial

port 0/0/0:15


Regards

Cristian

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 4 (2 ratings)
Loading.
cristian.munoz Tue, 03/27/2007 - 14:33
User Badges:

Dear Ale


Are you sure that this work?.

I made tests using 9.T and do not work.


paolo bevilacqua Tue, 03/27/2007 - 14:59
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

9.T and variations are indeed right in most cases. To find out why calls are failing, do "debug isdn q931" and "term mon".

cristian.munoz Tue, 03/27/2007 - 15:05
User Badges:

Dear Paolo


See the debug q931.


Mar 23 04:08:45.011: ISDN Se0/0/0:15 Q931: TX -> SETUP pd = 8 callref = 0x0091

Bearer Capability i = 0x8090A3

Standard = CCITT

Transfer Capability = Speech

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA9839F

Exclusive, Channel 31

Progress Ind i = 0x8183 - Origination address is non-ISDN

Calling Party Number i = 0x0180, '6912'

Plan:ISDN, Type:Unknown

Called Party Number i = 0x81

Plan:ISDN, Type:Unknown

*Mar 23 04:08:45.039: ISDN Se0/0/0:15 Q931: RX <- SETUP_ACK pd = 8 callref = 0x8091

Channel ID i = 0xA9839F

Exclusive, Channel 31

Progress Ind i = 0x8288 - In-band info or appropriate now available

*Mar 23 04:08:46.171: ISDN Se0/0/0:15 Q931: TX -> DISCONNECT pd = 8 callref = 0x0091

Cause i = 0x8090 - Normal call clearing

*Mar 23 04:08:46.191: ISDN Se0/0/0:15 Q931: RX <- RELEASE pd = 8 callref = 0x8091

*Mar 23 04:08:46.191: ISDN Se0/0/0:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x0091


paolo bevilacqua Tue, 03/27/2007 - 15:11
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

Hi, there is no called number in setup. Sorry, I'm not familiar with CCM/SRTS, hope someone can help better.



cristian.munoz Tue, 03/27/2007 - 15:39
User Badges:

Hi,I either i see it.

I configured SRST using FXO and it has work fine, but this is my first tiem using E1 PRI.

I access to E1 channel but i can?t dial the follow digits.

cristian.munoz Thu, 04/05/2007 - 05:56
User Badges:

Hi,

Who has any idea?

I can?t do outbound calls by E1 in FallBack mode.

paolo bevilacqua Thu, 04/05/2007 - 07:26
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

Hi,


please change the dial-peer for outgoing calls to:

destination-pattern 9T


check again with "debug isdn q931" what number goes out, if 9 is not removed, you will need to configure a translation-rule to remove it (not difficult).


Hope this helps, please rate all useful posts!

pacameron Sun, 04/08/2007 - 03:55
User Badges:
  • Silver, 250 points or more

Instead of using the 'access-code pri 9 direct-inward-dial' command, remove it and add 'secondary-dialtone 9'.


The 'access-code' commands actually creates temporary dial peers in the 20XXX range and these could be conflicting with your existing dial peers. You can check this by entering 'show call-manager-fallback dial-peer' while in SRST to see if this is happening.


With the 'secondary-dialtone 9' command, the router will play a different dial tone after dialing the '9' access code, this number and the rest of the digit string will then match on dial peer 100 (assuming the destination pattern on this dial peer is 9T) ... the leading 9 will be stripped off and the call should proceed correctly.



cristian.munoz Sun, 04/08/2007 - 07:06
User Badges:

Dear Paul


Last Thursday i run the command destiantion-pattern 9T and adding secondary-dialtone 9 , and this works!.

Thanks

Actions

This Discussion