FAX - CallMAnager 4.0 Router 2811

Unanswered Question
Apr 1st, 2007
User Badges:

Hello,


We are using CallManager 4.1 and router 2811.

We are using the router to get fax using:

dial-peer voice 833 pots

service onramp

incoming called-number XXXXXXX

direct-inward-dial

port 0/0/0:15

!

dial-peer voice 803 mmoip

service fax_on_vfc_onramp_app out-bound

destination-pattern XXXXXXX

information-type fax

session target mailto:[email protected]



Some time the tif come corrupted.

from the same fax some time it's come with no problem.

any idea?

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
msolak Sun, 04/01/2007 - 03:04
User Badges:
  • Silver, 250 points or more

1. check whether you have slips on your controller.


show controller e1 0/0/0


2.check whether your clock is syncronized.


network-clock-participate wic 0

network-clock-select 1 e1 0/0/0



regards



mehmet


idanlerer Sun, 04/01/2007 - 03:54
User Badges:

Thanks for helping


show controller e1 0/0/0

E1 0/0/0 is up.

Applique type is Channelized E1 - balanced

No alarms detected.

alarm-trigger is not set

Version info Firmware: 20040802, FPGA: 13, spm_count = 0

Framing is CRC4, Line Code is HDB3, Clock Source is Line.

CRC Threshold is 320. Reported from firmware is 320.

Data in current interval (460 seconds elapsed):

0 Line Code Violations, 0 Path Code Violations

0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

Data in Interval 1:

0 Line Code Violations, 0 Path Code Violations

0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

Data in Interval 2:

0 Line Code Violations, 0 Path Code Violations

0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

Data in Interval 3:

0 Line Code Violations, 0 Path Code Violations

0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

.

.

.

Data in Interval 96:

0 Line Code Violations, 0 Path Code Violations

0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs

Total Data (last 24 hours)

0 Line Code Violations, 0 Path Code Violations,

0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,

0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs


I try to rn the command

network-clock-participate wic 0

network-clock-select 1 e1 0/0/0


but error after network-clock-



Actions

This Discussion