04-03-2007 03:13 AM - edited 03-05-2019 03:16 PM
Hi Expert's
the ip default-gateway on the access switch should be the ip of the mangment Vlan or the ip of the SVI ?
10XS
Solved! Go to Solution.
04-03-2007 04:48 AM
Hi Ali,
Yes your default gateway config is perfect for access switch as well as for users in vlan 100.
Best of Luck.
Ankur
04-03-2007 03:21 AM
Hi Ali,
The IP default-gateway on the access-switch will be the IP address of the management vlan SVI of the core switch which is doing the inter-vlan routing.
http://www.cisco.com/en/US/products/ps6406/products_configuration_guide_chapter09186a008055fd17.html
HTH,
-amit singh
04-03-2007 03:35 AM
Hi Ali,
Let me take an example and you can use in your setup
If your access switch as interface vlan 1 with an ip address 1.1.1.1 255.255.255.0 then you must be having one SVI for this vlan 1 on your core switch also like 1.1.1.2 255.255.255.0 so in this scenario your default gateway on access switch should be 1.1.1.2.
HTH
Ankur
04-03-2007 03:58 AM
10XS FOR ALL UR REPLYS!
NOW I will make the ip default-gateway on the access switch belong to vlan 100 as the following:
core
int vlan 100
ip address 100.x.x.2/24
access switch:
ip default-gateway 100.100.100.2
2)default-gateway for users in vlan 100
D/G: 100.100.100.2
3)QUESTION REGARDING L3 Ether-channel
*************************************\
I HAVE 4507R WITH 2 Sup:
1)WS-X4515
2)WS-X4515
MODULES:WS-X4306-GB
I NEED 4 GIG AS L3 etherchannel to the Core,which ports u recomded to put on etherchannel?
am planning to put the following ports:
gig3/1
gig4/1
gig5/1
gig6/1
ur suggestion plz;what about the 4 gig ports on the 2 sup
regards
ALI
04-03-2007 04:18 AM
Hi,
1,2,3 is okay. Are you using stp?
You can use any of your gig for etherchannel. People choose them for their own sanity (standard), documentation, simplicity, availability, neat cabling :).
Your sup WS-X4515 has two gig each, The sup in slot 1 is primary while the sup in slot 2 is secondary. For etherchannel you only have a total of 2 gig both first port in sup.
04-03-2007 04:20 AM
Hi Ali,
Port channels using ports on different modules in same chassis is supported but instaed of using ports from all 4 modules you can use 3/1,3/2,4/1 and 4/2 again it is just a recommendation but you can design the way you want. Also run a command "sh port capability" and confirm if the ports on line card support etherchannel, it should but still you can confirm.
Because you have sup 4 in your chassis all 4 ports on supervisor cannot be active at a same time. Only gig1/1 and 2/1 will be active and once they go down 1/2 and 2/2 will become active.
HTH
Ankur
*Pls rate all helpfull post
04-03-2007 04:44 AM
Ankur my Freind!
no this config its good regarding ip default-gateway:
10XS FOR ALL UR REPLYS!
NOW I will make the ip default-gateway on the access switch belong to vlan 100 as the following:
core
int vlan 100
ip address 100.100.100.2/24
access switch:
ip default-gateway 100.100.100.2
2)default-gateway for users in vlan 100
D/G: 100.100.100.2
10xs
04-03-2007 04:48 AM
Hi Ali,
Yes your default gateway config is perfect for access switch as well as for users in vlan 100.
Best of Luck.
Ankur
04-03-2007 05:00 AM
Ankur my freind!
10xs a lot for ur great help as well for Amit
regards
ALI
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide