cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
428
Views
0
Helpful
5
Replies

Routing between Vlans

nouha1984
Level 1
Level 1

I have a catalyst 3560G with 3 vlans(Vlan1,Vlan2 and vlan3)and also one trunk port for vlan2 and vlan3.My question is how can i make a routing (Traffic exhange)between Vlan1 and vlan2?

5 Replies 5

Jon Marshall
Hall of Fame
Hall of Fame

Hi

3560(conf t)# int vlan 1

3560(config-if)# ip address x.x.x.x "subnet mask"

3560(config-if)# no shut

3560(conf t)# int vlan 2

3560(config-if)# ip address x.x.x.x "subnet mask"

3560(config-if)# no shut

Set your clients default gateway to the relevant vlan interface address ie

clients in vlan 2 have a default-gateway of the address you used when you created the vlan 2 interface.

HTH

Jon

This is my Catalyst configuration:

3560-G#sh run

Building configuration...

Current configuration : 2287 bytes

!

version 12.2

no service pad

service timestamps debug uptime

service timestamps log uptime

service password-encryption

!

!

!

no aaa new-model

ip subnet-zero

!

!

!

!

no file verify auto

spanning-tree mode pvst

spanning-tree extend system-id

!

vlan internal allocation policy ascending

!

interface GigabitEthernet0/1

!

interface GigabitEthernet0/2

!

interface GigabitEthernet0/3

!

interface GigabitEthernet0/4

!

interface GigabitEthernet0/5

!

interface GigabitEthernet0/6

!

interface GigabitEthernet0/7

!

interface GigabitEthernet0/8

!

interface GigabitEthernet0/9

!

interface GigabitEthernet0/10

!

interface GigabitEthernet0/11

!

interface GigabitEthernet0/12

!

interface GigabitEthernet0/13

!

interface GigabitEthernet0/14

!

interface GigabitEthernet0/15

!

interface GigabitEthernet0/16

!

interface GigabitEthernet0/17

switchport access vlan 36

switchport mode access

!

interface GigabitEthernet0/18

switchport access vlan 36

switchport mode access

!

interface GigabitEthernet0/19

switchport access vlan 69

switchport mode access

!

interface GigabitEthernet0/20

switchport access vlan 69

switchport mode access

!

interface GigabitEthernet0/21

switchport access vlan 69

switchport mode access

!

interface GigabitEthernet0/22

switchport access vlan 69

switchport mode access

!

interface GigabitEthernet0/23

switchport access vlan 36

switchport mode access

!

interface GigabitEthernet0/24

switchport trunk encapsulation dot1q

switchport trunk allowed vlan 36,69

switchport mode trunk

!

interface GigabitEthernet0/25

!

interface GigabitEthernet0/26

!

interface GigabitEthernet0/27

!

interface GigabitEthernet0/28

!

interface Vlan1

no ip address

no ip route-cache

!

interface Vlan69

ip address 192.168.3.2 255.255.255.0

no ip route-cache

!

ip default-gateway 192.168.3.1

ip classless

ip http server

!

!

where Vlan 36: 192.168.1.0/24

Vlan 1: 192.168.2.0/24

I want to add a new commands to make routing between Vlan 36 and Vlan 1 only for traffic data.

So please can you help me.

Hi

3560(conf t)# int vlan 1

3560(config-if)# ip address 192.168.2.1 255.255.255.0

3560(config-if)# no shut

3560(conf t)# int vlan 36

3560(config-if)# ip address 192.168.1.1 255.255.255.0

3560(config-if)# no shut

HTH

Jon

In addition to Jon's post, you have enable " ip routing on the switch as well.You dont have " ip routing" enabled on the switch. Do this:

3560(conf t)# ip routing

3560#Wr mem

You will be good to go.

HTH,Please rate if it does.

-amit singh

Hi

Can u tell that these 3560Gs are connected to which other switches/routers.And moreover how?

Would be better if u would attach your network diagram.

Regards

JD

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: