04-24-2007 12:59 AM - edited 03-05-2019 03:38 PM
I have a catalyst 3560G with 3 vlans(Vlan1,Vlan2 and vlan3)and also one trunk port for vlan2 and vlan3.My question is how can i make a routing (Traffic exhange)between Vlan1 and vlan2?
04-24-2007 01:16 AM
Hi
3560(conf t)# int vlan 1
3560(config-if)# ip address x.x.x.x "subnet mask"
3560(config-if)# no shut
3560(conf t)# int vlan 2
3560(config-if)# ip address x.x.x.x "subnet mask"
3560(config-if)# no shut
Set your clients default gateway to the relevant vlan interface address ie
clients in vlan 2 have a default-gateway of the address you used when you created the vlan 2 interface.
HTH
Jon
04-24-2007 01:47 AM
This is my Catalyst configuration:
3560-G#sh run
Building configuration...
Current configuration : 2287 bytes
!
version 12.2
no service pad
service timestamps debug uptime
service timestamps log uptime
service password-encryption
!
!
!
no aaa new-model
ip subnet-zero
!
!
!
!
no file verify auto
spanning-tree mode pvst
spanning-tree extend system-id
!
vlan internal allocation policy ascending
!
interface GigabitEthernet0/1
!
interface GigabitEthernet0/2
!
interface GigabitEthernet0/3
!
interface GigabitEthernet0/4
!
interface GigabitEthernet0/5
!
interface GigabitEthernet0/6
!
interface GigabitEthernet0/7
!
interface GigabitEthernet0/8
!
interface GigabitEthernet0/9
!
interface GigabitEthernet0/10
!
interface GigabitEthernet0/11
!
interface GigabitEthernet0/12
!
interface GigabitEthernet0/13
!
interface GigabitEthernet0/14
!
interface GigabitEthernet0/15
!
interface GigabitEthernet0/16
!
interface GigabitEthernet0/17
switchport access vlan 36
switchport mode access
!
interface GigabitEthernet0/18
switchport access vlan 36
switchport mode access
!
interface GigabitEthernet0/19
switchport access vlan 69
switchport mode access
!
interface GigabitEthernet0/20
switchport access vlan 69
switchport mode access
!
interface GigabitEthernet0/21
switchport access vlan 69
switchport mode access
!
interface GigabitEthernet0/22
switchport access vlan 69
switchport mode access
!
interface GigabitEthernet0/23
switchport access vlan 36
switchport mode access
!
interface GigabitEthernet0/24
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 36,69
switchport mode trunk
!
interface GigabitEthernet0/25
!
interface GigabitEthernet0/26
!
interface GigabitEthernet0/27
!
interface GigabitEthernet0/28
!
interface Vlan1
no ip address
no ip route-cache
!
interface Vlan69
ip address 192.168.3.2 255.255.255.0
no ip route-cache
!
ip default-gateway 192.168.3.1
ip classless
ip http server
!
!
where Vlan 36: 192.168.1.0/24
Vlan 1: 192.168.2.0/24
I want to add a new commands to make routing between Vlan 36 and Vlan 1 only for traffic data.
So please can you help me.
04-24-2007 01:54 AM
Hi
3560(conf t)# int vlan 1
3560(config-if)# ip address 192.168.2.1 255.255.255.0
3560(config-if)# no shut
3560(conf t)# int vlan 36
3560(config-if)# ip address 192.168.1.1 255.255.255.0
3560(config-if)# no shut
HTH
Jon
04-24-2007 01:56 AM
In addition to Jon's post, you have enable " ip routing on the switch as well.You dont have " ip routing" enabled on the switch. Do this:
3560(conf t)# ip routing
3560#Wr mem
You will be good to go.
HTH,Please rate if it does.
-amit singh
04-24-2007 01:59 AM
Hi
Can u tell that these 3560Gs are connected to which other switches/routers.And moreover how?
Would be better if u would attach your network diagram.
Regards
JD
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide