Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
1006
Views
25
Helpful
11
Replies

cat4000-i9s-mz.121-19.EW1.bin

alsayed
Level 1
Level 1

‎05-01-2007 09:41 AM - edited ‎03-05-2019 03:47 PM

hello!

i have read a reply FROM Ankur that the switchover in the RPR Mode between 3 to 4 Mts & 30 to 60 Seconds in RPR +.but on my 4507R(2 Sup WS-X4515)i saw just RPR,.CAN I Upgrade my IOS To support RPR+?30 Sec its goof for Switch over

My Current IOS:cat4000-i9s-mz.121-19.EW1.bin

Labels:
0 Helpful
11 Replies 11

situwayne
Level 1
Level 1

‎05-01-2007 09:47 AM

why not consider SSO?

0 Helpful

wochanda
Level 4
Level 4

‎05-01-2007 09:47 AM

You can upgrade to 12.2(25)EWA to have SSO and get <30s switchovers or 12.2(31)SGA code to support SSO with NSF, to have possible >5s switchovers. Here is the link for 12.2SGA SSO with NSF:

http://www.cisco.com/univercd/cc/td/doc/product/lan/cat4000/12_2_31a/config/nsfwsso.htm

Amit Singh
Cisco Employee
Cisco Employee

‎05-01-2007 09:51 AM

Hi Ali,

I would suggest to use SSO with NFS between the supervisor engines. SSO/NSF give you sub-milisecond fail-over between the sup's for both L2/L3 failover though we claim it around 0-3 seconds which depends on the traffic flow. My self has tested same with 900Mbps traffic and the failover time was arnd 300 milisecond.

You need atleaset 12.2.31SG for the same.

http://www.cisco.com/univercd/cc/td/doc/product/lan/cat4000/12_2_31s/conf/nsfwsso.htm

HTH,

-amit singh

alsayed
Level 1
Level 1
In response to Amit Singh

‎05-01-2007 09:53 AM

Hi Amit!

plz give the full name of the IOS

10XS

0 Helpful

alsayed
Level 1
Level 1
In response to alsayed

‎05-01-2007 09:57 AM

Hi!

do i need to update the IOS ON BOTH Supervisor or Just on 1 of them

10xs

0 Helpful

alsayed
Level 1
Level 1
In response to alsayed

‎05-01-2007 10:09 AM

ANY REPLY HERE

0 Helpful

Amit Singh
Cisco Employee
Cisco Employee
In response to alsayed

‎05-02-2007 12:50 AM

Hi Ali,

This is the full image name that you need on the box :

cat4500-ipbase-mz

HTH,

-amit singh

ankbhasi
Cisco Employee
Cisco Employee
In response to alsayed

‎05-02-2007 12:52 AM

Hi Ali,

Have a look at this release notes for supported IOS 12.2(31)SG

http://www.cisco.com/en/US/products/hw/switches/ps4324/prod_release_note09186a0080758ff3.html#wp686916

HTH

Ankur

alsayed
Level 1
Level 1
In response to ankbhasi

‎05-02-2007 03:47 AM

Hello Ankur;Hello Amit!

do i need to copy this IOS cat4500-ipbase-mz

TO Both bootflash on the 2 sup.or just on 1 bootflash???

plz send me the Link to to this

10xs

0 Helpful

ankbhasi
Cisco Employee
Cisco Employee
In response to alsayed

‎05-02-2007 05:35 AM

Hi Ali,

You have to copy the image on both bootflash.

This link will help you doing upgrade on both the supervisors.

http://www.cisco.com/en/US/products/hw/switches/ps4324/products_configuration_guide_chapter09186a008036715c.html#wp1104060

HTH

Ankur

alsayed
Level 1
Level 1
In response to ankbhasi

‎05-02-2007 09:15 AM

Ankur My Freind

10xs

0 Helpful
Customers Also Viewed These Support Documents
Review Cisco Networking products for a $25 gift card