Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
490
Views
0
Helpful
5
Replies

Move from F/R to E1 leased line 2Mb channel, need advise

Go to solution
winanjaya
Level 1
Level 1

‎05-01-2007 11:00 PM - edited ‎03-03-2019 04:46 PM

Dear Expert,

Currently we have 4 Frame Relay connection to branches (A (as HO) to B,C,D,E), we plan to move to E1 leased line 2Mb channel from A to B,C,D,E my question is: is it necessary for me to buy some peripheral ?, below are what I had when "show version"

3640 -> A (HO)

cisco 3640 (R4700) processor (revision 0x00) with 73728K/24576K bytes of memory.

Processor board ID 26875657

R4700 CPU at 100Mhz, Implementation 33, Rev 1.0

Bridging software.

X.25 software, Version 3.0.0.

SuperLAT software (copyright 1990 by Meridian Technology Corp).

1 FastEthernet/IEEE 802.3 interface(s)

2 Serial(sync/async) network interface(s)

8 terminal line(s)

4 Voice FXS interface(s)

DRAM configuration is 64 bits wide with parity disabled.

125K bytes of non-volatile configuration memory.

16384K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

2620 -> B

cisco 2620 (MPC860) processor (revision 0x00) with 45056K/4096K bytes of memory.

Processor board ID JAD0622098M (1466765479)

M860 processor: part number 0, mask 49

Bridging software.

X.25 software, Version 3.0.0.

1 FastEthernet/IEEE 802.3 interface(s)

1 Serial network interface(s)

2 Voice FXS interface(s)

32K bytes of non-volatile configuration memory.

16384K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

1760 -> C

cisco 1760 (MPC860P) processor (revision 0x200) with 58983K/6553K bytes of memory.

Processor board ID VMS06200HRY (152575307), with hardware revision BB67

MPC860P processor: part number 5, mask 2

Bridging software.

X.25 software, Version 3.0.0.

1 FastEthernet/IEEE 802.3 interface(s)

1 Serial(sync/async) network interface(s)

2 Voice FXS interface(s)

32K bytes of non-volatile configuration memory.

32768K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

1760 -> D

cisco 1760 (MPC860P) processor (revision 0x200) with 58983K/6553K bytes of memor

y.

Processor board ID VMS06190GJR (4215553861), with hardware revision BB67

MPC860P processor: part number 5, mask 2

Bridging software.

X.25 software, Version 3.0.0.

1 FastEthernet/IEEE 802.3 interface(s)

1 Serial(sync/async) network interface(s)

2 Voice FXS interface(s)

32K bytes of non-volatile configuration memory.

32768K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

1760 -> E

cisco 1760 (MPC860P) processor (revision 0x200) with 58983K/6553K bytes of memor

y.

Processor board ID VMS06190H4G (2625338763), with hardware revision BB67

MPC860P processor: part number 5, mask 2

Bridging software.

X.25 software, Version 3.0.0.

1 FastEthernet/IEEE 802.3 interface(s)

1 Serial(sync/async) network interface(s)

2 Voice FXS interface(s)

32K bytes of non-volatile configuration memory.

32768K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

Labels:
0 Helpful
1 Accepted Solution

Accepted Solutions

Go to solution
mohammedmahmoud
Level 11
Level 11
In response to winanjaya

‎05-02-2007 12:42 AM

Hi,

Cisco 3640 supports up to 128 MB of DRAM:

http://www.cisco.com/en/US/products/hw/routers/ps274/prod_bulletin09186a0080091f70.html

HTH, please rate using the scroll box below if it does help,

Mohammed Mahmoud.

View solution in original post

0 Helpful
5 Replies 5

Go to solution
mohammedmahmoud
Level 11
Level 11

‎05-01-2007 11:29 PM

Hi,

If i understand you right, you'll need 4 serial interfaces on the HO, one for each site, and 1 serial interface at each site (Hub and spoke topology).

HTH, please rate if it does help,

Mohammed Mahmoud.

0 Helpful

Go to solution
winanjaya
Level 1
Level 1
In response to mohammedmahmoud

‎05-01-2007 11:43 PM

Thanks, but could you please more spesific, what part should I use? and BTW do I need to upgrade the IOS also? and on HO, does CISCO 3640 can support 4 serial interfaces? ..

thanks & regards

Winanjaya

0 Helpful

Go to solution
mohammedmahmoud
Level 11
Level 11
In response to winanjaya

‎05-02-2007 12:03 AM

Hi Winanjaya,

To connect your routers via leased lines, with the HO router as a Hub, you'll need a serial interface on the Hub router for each spoke, accordingly you'll need 4 serial interfaces on the HO router, the 3640 can support the 4 serial interfaces, you can use this NM-4T interface:

http://www.cisco.com/en/US/products/hw/routers/ps274/products_tech_note09186a00800a93f3.shtml

HTH, please rate using the scroll box below if it does help,

Mohammed Mahmoud.

0 Helpful

Go to solution
winanjaya
Level 1
Level 1
In response to mohammedmahmoud

‎05-02-2007 12:35 AM

Thanks, what's the max. RAM can be installed on CISCO 3640? thanks and regards

Winanjaya

0 Helpful

Go to solution
mohammedmahmoud
Level 11
Level 11
In response to winanjaya

‎05-02-2007 12:42 AM

Hi,

Cisco 3640 supports up to 128 MB of DRAM:

http://www.cisco.com/en/US/products/hw/routers/ps274/prod_bulletin09186a0080091f70.html

HTH, please rate using the scroll box below if it does help,

Mohammed Mahmoud.

0 Helpful
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Customers Also Viewed These Support Documents
Review Cisco Networking products for a $25 gift card