cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
795
Views
35
Helpful
15
Replies

4507R Orange State on gig1/1 on sup 1

alsayed
Level 1
Level 1

Hello!

yesterday;we bought a refurbish Switch 4507R;i did to it a basic config;the switch its not in production yet.but i have seen the light is orange on the gig1/1 on the sup1 & yelow on the 2nd sup

is there any problem?plz explain

10xs

output

********

Mod Ports Card Type Model Serial No.

---+-----+--------------------------------------+------------------+-----------

1 2 1000BaseX (GBIC) Supervisor(active) WS-X4515 JAE07340WML

2 Standby Supervisor

3 6 1000BaseX (GBIC) WS-X4306-GB JAE07410ZBL

4 6 1000BaseX (GBIC) WS-X4306-GB JAE0736148W

5 6 1000BaseX (GBIC) WS-X4306-GB JAE07371DQL

6 6 1000BaseX (GBIC) WS-X4306-GB JAE073618DK

M MAC addresses Hw Fw Sw Status

--+--------------------------------+---+------------+----------------+---------

1 000d.ed90.cbc0 to 000d.ed90.cbc1 3.0 12.1(12r)EW 12.1(19)EW1, EAR Ok

2 Unknown Unknown Unknown Other

3 000b.5fb7.04ae to 000b.5fb7.04b3 2.2 Ok

4 000d.6504.3996 to 000d.6504.399b 2.2 Ok

5 000b.5fb6.f074 to 000b.5fb6.f079 2.2 Ok

6 000d.6504.38f4 to 000d.6504.38f9 2.2 Ok

System Failures:

----------------

Cisco Internetwork Operating System Software

IOS (tm) Catalyst 4000 L3 Switch Software (cat4000-I9S-M), Version 12.1(19)EW1, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

TAC Support: http://www.cisco.com/tac

Copyright (c) 1986-2003 by cisco Systems, Inc.

Compiled Mon 28-Jul-03 16:10 by eaarmas

Image text-base: 0x00000000, data-base: 0x00F12E30

ROM: 12.1(12r)EW

Dagobah Revision 86, Swamp Revision 28

x uptime is 20 minutes

System returned to ROM by power-on

******************************************GigabitEthernet1/1 is down, line protocol is down (notconnect)

Hardware is Gigabit Ethernet Port, address is 000d.ed90.cbc0 (bia 000d.ed90.cbc0)

Description: "Trunk to xxxxx

MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation ARPA, loopback not set

Keepalive set (10 sec)

Auto-duplex, Auto-speed

input flow-control is off, output flow-control is off

ARP type: ARPA, ARP Timeout 04:00:00

Last input never, output never, output hang never

Last clearing of "show interface" counters never

Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0

Queueing strategy: fifo

Output queue: 0/40 (size/max)

5 minute input rate 0 bits/sec, 0 packets/sec

5 minute output rate 0 bits/sec, 0 packets/sec

0 packets input, 0 bytes, 0 no buffer

Received 0 broadcasts (0 multicast)

0 runts, 0 giants, 0 throttles

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored

0 input packets with dribble condition detected

System image file is "bootflash:cat4000-i9s-mz.121-19.EW1.bin"

cisco WS-C4507R (XPC8245) processor (revision 7) with 524288K bytes of memory.

Processor board ID FOX073502WX

Last reset from PowerUp

28 Gigabit Ethernet/IEEE 802.3 interface(s)

403K bytes of non-volatile configuration memory.

Configuration register is 0x2102

Regards

Ali

1 Accepted Solution

Accepted Solutions

Hi Ali,

As per teh output you have posted everything looks good. I believe gig interface must be showing orange led because nothing is connected to that interface. So try connecting some switch to gig interface on sup in slot 1 and see if the led changes to green.

I am really not sure about yellow led light. Can you confirm the yellow led light is shown for interface or system? I mean where exactly you see yellow light what is wriiten on side of the led light.

Regards,

Ankur

View solution in original post

15 Replies 15

ankbhasi
Cisco Employee
Cisco Employee

Hi Ali,

Your second sup is not recognised by the system and it is in "UNKNOWN STATE" you can see that from "sh mod" command and is the reason the link light is yellow on sup 2.

Now I am not sure if the sup in slot 2 is exact same hardware or not which is there on slot 1. If it is not the exact same hardware then the second sup will go in UNKNOWN STATE.

Other reason of it being in this state is may be it does not have a valid IOS or wrong boot path set because of which it is in rommon state which you need to console and check the status.

HTH

Ankur

eofelt
Level 1
Level 1

If it's not an IOS miss match (they have to be running the same code) then most likey, it's a ROMmon issue.

If the standby module is not operational because it is in ROMmon or other reasons, or it is not present.

http://www.cisco.com/en/US/products/hw/switches/ps4324/products_configuration_guide_chapter09186a008011c8ad.html

Standby Supervisor Engine Module Is Not Online or Status Indicates Other...

http://www.cisco.com/warp/public/473/165.html

Also, look at:

switch#show diagnostic content module 2

switch#show diagnostic result module 2

There's more, but looks at these first and

let us know.

Hello!

but why the First 1 is orange;& The Second One is in yello State?plz explain

Ali

Hi Ali,

I am not sure of yellow light. But you mention yellow light is on second sup correct? Your second sup is not recognised by the system so it must be behaving weird.

Coming to the orange light I believe you see the link light as orange correct ? if yes it indicates the link is disabled by user.

Can you try connecting some other switch to the gig interface and see if the link comes up.

Regards,

Ankur

Ankur My Freind!

I Attached the output of the show module all command

yes the Status light on the 1st Sup is Orange

The Status light on the 2nd Sup is Yellow,and my Console on the 1st one which is Booting Propperly

My Freind What Happend

Regards

ALI

Hi Ali,

Nothing major had happened. We just need to sort out things one by one. First console into the second sup and see if you get anything on console?

If not just take out the second sup from the chassis and then check connect some oether switch on gig1/1 and check the status.

Right now I believe nothing is connedted to gig1/1?

Regards,

Ankur

Hi

it was Romon Mode & Missed the Bootvariable;i issue the Sh module the Unknown State disappear;but i noticed that the system Hang on this Screan:

Cisco Internetwork Operating System Software

IOS (tm) Catalyst 4000 L3 Switch Software (cat4000-I9S-M), Version 12.1(19)EW1, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

TAC Support: http://www.cisco.com/tac

Copyright (c) 1986-2003 by cisco Systems, Inc.

Compiled Mon 28-Jul-03 16:10 by eaarmas

Image text-base: 0x00000000, data-base: 0x00F12E30

Compressed configuration from 6631 bytes to 2608 bytes[OK][OK]

***********************************

* STANDBY SUPERVISOR *

* REDUNDANCY mode is RPR *

* Waiting for Switchover Activity *

***********************************

10xs

Hi Ali,

Once the standby sup comes up fine the console connection for standby sup gets disabled so you will not see any activity and it will remain in the state which you see at teh time of initial boot.

You can console into the active sup and check the status and as you mentioned I believe it must be showing "standby and OK status now", can you confirm this by pasting "sh mod" command.

Also what is the status of led light on stanby sup and what is the status of led light on active sup?

Regards,

Ankur

Ankur My Freind!

Plz Have a Look to attched File.

om sup 1:The Led on the Active sup Still Orange

on Sup 2:The Led on the standby sup Still yellow

Hi Ali,

As per teh output you have posted everything looks good. I believe gig interface must be showing orange led because nothing is connected to that interface. So try connecting some switch to gig interface on sup in slot 1 and see if the led changes to green.

I am really not sure about yellow led light. Can you confirm the yellow led light is shown for interface or system? I mean where exactly you see yellow light what is wriiten on side of the led light.

Regards,

Ankur

I think the port with orrange light is in shutdown state, please go to the interface and do it as "no shut", the light should go off. Do you have something connected on the port on second sup where you are getting a yello light. I think it should be green, if you have a connection on it and its up.

-amit singh

my freinds Ankur/Amit

Thanks a Lot for Help

Regards

Ali

Ankur My Freind!

sup1 Status=orange

sup2=status=yellow

I Do Appreciate ur Help Always to me Since 1 Years

10xs Ankur

Hi Ali,

Status light Orange means its "System boot or diagnostic test is in progress" which i do not think is your case. The correct status should be green.

Can you confirm if you connect some switch to the gig interface, the gig interface led changes to green. Also does this switch have some configuration and ip address assigned? Can you ping this switch?

Also can you attach the outputs of

show module

show env

show power

Show bootflash:

show boot

show redundancy

show diagnostic result module 1 detail

show diagnostic result module 2 detail

Regards,

Ankur

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Innovations in Cisco Full Stack Observability - A new webinar from Cisco