NM-HDV2-1T1/E1 Not working

Unanswered Question
May 21st, 2007
User Badges:

Hi all,


I just received a brand new 2811 with a NM-HDV2-1T1/E1 module to be connected to an E1 ISDN PRI interface.


However, the integrated E1 interface just can?t establish the ISDN framing with the PBX. I inserted a VWIC2-1MFT-T1/E1 into this module, configured the port and voila! the ISDN framing came up right away.


So... it seems the integrated port on the module is DOA, but since this is a new module to me I want to be sure I?m not missing something before requesting a RMA.


Am I missing something besides issuing the card type e1 command?


Thanks in advance


  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
Paolo Bevilacqua Mon, 05/21/2007 - 16:32
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

HI, can you check if the settings are the same for impedance and crc ?

carlosv Mon, 05/21/2007 - 16:39
User Badges:

Thanks for taking your time.


Yes, both are the same. All the config is exactly the same except for the port number. I use the cables to the PBX for both ports. The DSPs are ok and I can assign them to both cards.


Hi Carlos

T1/E1 cards need the IOS release 12.4.

You first must enable the of the card as E1 then I will be able to configure like a normal E1.

When you look the card is like totally dead but is not.

HERE SOME PART OF THE CAPTURE, when I worked with this kind of card.


version 12.4

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname CCME_PQ

!

boot-start-marker

boot-end-marker

!

card type e1 0 2

------

network-clock-participate wic 2

network-clock-select 1 E1 0/2/0

----------

!

!

controller E1 0/2/0

pri-group timeslots 1-31

!

------------------

!

interface Serial0/2/0:15

no ip address

encapsulation hdlc

isdn switch-type primary-net5

isdn incoming-voice voice

no cdp enable

!


REGARDS

WALTER FLORES

--------------------------






carlosv Wed, 05/23/2007 - 09:20
User Badges:



Thank you Walter,


However, the configuration with the VWIC card is working, what I need is to know how to make it work with a single NM-HDV2-1T1/E1 without an extra VWIC card. This is the relevant configuration:



!

card type e1 1 0

card type e1 1 1

!

network-clock-participate slot 1

network-clock-select 1 E1 1/0

!

isdn switch-type primary-qsig

!

controller E1 1/0

framing NO-CRC4

pri-group timeslots 1-8,16

!

controller E1 1/0/0

framing NO-CRC4

pri-group timeslots 1-8,16

!

interface Serial1/0:15

no ip address

encapsulation hdlc

isdn switch-type primary-qsig

isdn overlap-receiving

isdn incoming-voice voice

isdn send-alerting

no cdp enable

!

interface Serial1/0/0:15

no ip address

encapsulation hdlc

isdn switch-type primary-qsig

isdn overlap-receiving

isdn incoming-voice voice

isdn send-alerting

no cdp enable

!

voice-port 1/0:15

cptone DE

timeouts interdigit 30

timeouts wait-release 3

!

voice-port 1/0/0:15

cptone DE

timeouts interdigit 30

timeouts wait-release 3


The controller E1 1/0/0 is the VWIC port, E1 1/0 is the integrated port. If I plug the PBX cable on the first one everything works great, when I change to the other one doesn't.

TIA.

Actions

This Discussion