ATOM Cisco 7206VXR (NPE-G2)

Unanswered Question
May 26th, 2007

I try to configure ATOM in two 7206VXR (NPE-G2) routers as the following

-first router

interface ATM2/0.100 point-to-point

no snmp trap link-status

pvc 0/1234 l2transport

xconnect 10.1.1.1 50 encapsulation mpls

-second router

interface ATM2/0.100 point-to-point

no snmp trap link-status

pvc 0/1234 l2transport

xconnect 10.1.1.2 50 encapsulation mpls

But vc is down

Local intf Local circuit Dest address VC ID Status

------------- -------------------------- --------------- ---------- ----------

AT2/0.100 ATM AAL5 0/100 10.1.1.1 50 DOWN

I need to know if 7206VXR (NPE-G2) support ATOM configuration or not

----------------------------------

PE#show ver

Cisco IOS Software, 7200 Software (C7200P-ADVIPSERVICESK9-M), Version 12.4(11)T1, RELEASE SOFTWARE (fc5)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2007 by Cisco Systems, Inc.

Compiled Thu 25-Jan-07 20:33 by prod_rel_team

ROM: System Bootstrap, Version 12.4(4r)XD5, RELEASE SOFTWARE (fc1)

BOOTLDR: Cisco IOS Software, 7200 Software (C7200P-KBOOT-M), Version 12.4(4)XD2, RELEASE SOFTWARE (fc2)

Suez_PE uptime is 1 week, 3 days, 5 minutes

System returned to ROM by reload at 11:20:47 CAI Wed May 16 2007

System restarted at 19:29:04 CAI Wed May 16 2007

System image file is "disk2:c7200p-advipservicesk9-mz.124-11.T1.bin"

Last reload reason: Reload Command

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

[email protected].

Cisco 7206VXR (NPE-G2) processor (revision A) with 917504K/65536K bytes of memory.

Processor board ID 35245323

MPC7448 CPU at 1666Mhz, Implementation 0, Rev 2.1

6 slot VXR midplane, Version 2.11

Last reset from power-on

PCI bus mb1 (Slots 1, 3 and 5) has a capacity of 600 bandwidth points.

Current configuration on bus mb1 has a total of 90 bandwidth points.

This configuration is within the PCI bus capacity and is supported.

PCI bus mb2 (Slots 2, 4 and 6) has a capacity of 600 bandwidth points.

Current configuration on bus mb2 has a total of 270 bandwidth points.

This configuration is within the PCI bus capacity and is supported.

Please refer to the following document "Cisco 7200 Series Port Adaptor

Hardware Configuration Guidelines" on Cisco.com <http://www.cisco.com>

for c7200 bandwidth points oversubscription and usage guidelines.

1 FastEthernet interface

3 Gigabit Ethernet interfaces

2 Serial interfaces

2 ATM interfaces

2045K bytes of NVRAM.

500472K bytes of ATA PCMCIA card at slot 2 (Sector size 512 bytes).

65536K bytes of Flash internal SIMM (Sector size 512K).

Configuration register is 0x2102

I have this problem too.
0 votes
  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
mrcomm2000 Sun, 05/27/2007 - 05:47

Dear mohhamed

I made the same configuration in 2 routers Cisco 7206VXR (NPE-G1) with IOS c7200-js-mz.123-8.T5.bin and vc is up

Local intf Local circuit Dest address VC ID Status

------------- -------------------- --------------- ---------- ----------

AT1/0.300 ATM AAL5 2/300 10.1.1.3 300 UP

Please advice

thank you

Paolo Bevilacqua Sun, 05/27/2007 - 08:41

Hi,

If same configuration fails on the newer IOS/NPE, suggest you contact the TAC for the due support.

Rahul Kachalia Sun, 05/27/2007 - 12:55

If possible pls provide output of following cmds:

s int at2/0

s mpls l2 vc det

s mpls int

s mpls ldp neighbor

s ip route 10.1.1.1

s ip route 10.1.1.2

thanks,

rahul.

Actions

This Discussion