PVDM2-12DM

Unanswered Question
Jun 5th, 2007
User Badges:

I have a problem with PVDM2-12DM. I have installed a PVDM2-12DM in a Cisco 2811 with a E1 Controller.

The Output of show diag. is the following.

PVDM Slot 0:

No Card PVDM daughter card

Hardware Revision : 1.0

Part Number : 73-10100-03

Board Revision : B0

Deviation Number : 84758

Fab Version : 03

PCB Serial Number : FOC10223PUR

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Processor type : 00

Product (FRU) Number : PVDM2-12DM

Version Identifier : V01

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 04 8E 41 01 00 82 49 27 74 03 42 42 30

0x10: 88 00 01 4B 16 02 03 C1 8B 46 4F 43 31 30 32 32

0x20: 33 50 55 52 03 00 81 00 00 00 00 04 00 09 00 CB

0x30: 8A 50 56 44 4D 32 2D 31 32 44 4D 89 56 30 31 20

0x40: D9 02 40 C1 FF FF FF FF FF FF FF FF FF FF FF FF

0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

-------------------

- What the meaning of "No Card PVDM daughter card"?

- The LED on the router for PVDM0 and PVDM1 is not active . Whay ?.


can somebody help.

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
Paolo Bevilacqua Tue, 06/05/2007 - 13:20
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

Hello,


the "No Card" part of the output appears to be a cosmetic bug, does the pvdm2 actually work ?

giaaaj Tue, 06/05/2007 - 23:51
User Badges:

No it does not work.

The LED on the Router is inactive and i am not able to configure it in a line command


ACCG007(config)#line ?

<0-326> First Line number

aux Auxiliary line

console Primary terminal line

tty Terminal controller

vty Virtual terminal

x/y Slot/Port for Modems

x/y/z Slot/Subslot/Port for Modems


actualy for a PVDM2-12DM i should be able to configure the line from 322 to 333 ( 12 lines) but i see only the outbut obove.

in an interface Group-Async0

iam not able to configure the group of lines 322-333 see output:

ACCG007(config)#interface Group-Async0

ACCG007(config-if)#grou

ACCG007(config-if)#group-range ?

<1-320> Start of range

tty Terminal controller

x/y Slot/Port for Modems

x/y/z Slot/Subslot/Port for Modems


ACCG007(config-if)#group-range


Thx


Ali

Paolo Bevilacqua Wed, 06/06/2007 - 00:20
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

Hello,


IOS used? Configuration? Is there an NM-PRI installed ?

giaaaj Fri, 06/15/2007 - 01:45
User Badges:

Hi,

The problem is solved by upgrading the IOS

Actions

This Discussion