cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
230
Views
5
Helpful
1
Replies

No output on show run

bedevere.curry
Level 1
Level 1

We have an issue with our 7200. We can't output the show run, wr term, other show command works. Is there a way to resolve this?

thanks

spdum1edmz2r01#show version

Cisco Internetwork Operating System Software

IOS (tm) 7200 Software (C7200-IS-M), Version 12.0(7)XE1, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

TAC:Home:SW:IOS:Specials for info

Copyright (c) 1986-2000 by cisco Systems, Inc.

Compiled Fri 04-Feb-00 21:31 by lstringr

Image text-base: 0x60008900, data-base: 0x60FF4000

ROM: System Bootstrap, Version 11.1(13)CA, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

BOOTFLASH: 7200 Software (C7200-BOOT-M), Version 12.0(10)S, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

spdum1edmz2r01 uptime is 11 weeks, 5 days, 5 hours, 30 minutes

System returned to ROM by reload at 21:16:29 BRA Thu Mar 29 2007

System restarted at 21:18:06 BRA Thu Mar 29 2007

System image file is "slot0:c7200-is-mz.120-7.XE1"

cisco 7206 (NPE200) processor with 57344K/8192K bytes of memory.

R5000 CPU at 200Mhz, Implementation 35, Rev 2.1, 512KB L2 Cache

6 slot midplane, Version 1.3

Last reset from power-on

Bridging software.

X.25 software, Version 3.0.0.

24 Ethernet/IEEE 802.3 interface(s)

2 FastEthernet/IEEE 802.3 interface(s)

125K bytes of non-volatile configuration memory.

4096K bytes of packet SRAM memory.

20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K).

4096K bytes of Flash internal SIMM (Sector size 256K).

Configuration register is 0x102

spdum1edmz2r01#show rim

spdum1edmz2r01#show run

spdum1edmz2r01#show running-config

spdum1edmz2r01#dir nv

spdum1edmz2r01#dir nvram:

Directory of nvram:/

1 -rw- 53202 <no date> startup-config

2 ---- 26 <no date> private-config

3 -rw- 53202 <no date> underlying-config

129016 bytes total (75814 bytes free)

spdum1edmz2r01#dir /all flaa

spdum1edmz2r01#dir /all fla

spdum1edmz2r01#dir /all flash:

Directory of slot0:/

1 -rw- 9239932 Jun 22 2000 23:01:07 c7200-is-mz.120-7.XE1

2 -rw- 273384 Dec 07 2002 23:30:52 config

20578304 bytes total (11064732 bytes free)

spdum1edmz2r01#

1 Reply 1

guruprasadr
Level 7
Level 7

HI, [Pls Rate if Helps]

Error in: Configuration Register Setting...

Your COnfiguration Register set is: 0x102

Set your Configuration Register Value to:

"Configuration register is 0x2102"

INFO: On power-up or reload, this router will load the IOS image stored in flash-RAM

(assuming one exists). If no valid IOS image or flash-RAM exists, this router will attempt to boot in order of following methods:

- boot system commands

- a TFTP-server (using a default IOS image filename)

INFO: On power-up or reload, this router will load it's configuration from a file

stored in NVRAM.

WARNING: On power-up or reload, if an error occurs with it's prescribed IOS boot method(s), this router will not boot into the fall-back (reduced) IOS image stored on ROM (sometimes called ROM-boot or boot-strap mode)

TRY THIS: To restore the router's fall-back ROM-boot to default function, enter

configuration mode and reset the configuration register with the 'config-register' command. Set the 13th low-order bit (from the right) of the register to binary 0. (You'll have to convert the final register value from binary to hexadecimal

0xABCD) for the 'config-register' command.)

PLS RATE if HELPS

Best Regards,

Guru Prasad R

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: