'sh int' on 7604 not showing all the interfaces

Unanswered Question
Jun 20th, 2007

In my 7604, 12.2(33)SRB1, I have a couple SIP-400s with 2GE-SPAs in them. Here is 'sh mod':

ROC-RT7604A-CR>sh mod

Mod Ports Card Type Model Serial No.

--- ----- -------------------------------------- ------------------ -----------

1 2 Supervisor Engine 720 (Active) WS-SUP720-3B SAL1106GKP2

2 0 4-subslot SPA Interface Processor-400 7600-SIP-400 JAE1112A45Z

Mod MAC addresses Hw Fw Sw Status

--- ---------------------------------- ------ ------------ ------------ -------

1 0017.9444.68fc to 0017.9444.68ff 5.3 8.4(2) 12.2(33)SRB1 Ok

2 0015.2b89.a1d0 to 0015.2b89.a24f 2.4 12.2(33)SRB1 12.2(33)SRB1 Ok

Mod Sub-Module Model Serial Hw Status

---- --------------------------- ------------------ ----------- ------- -------

1 Policy Feature Card 3 WS-F6K-PFC3B SAL1106GLRR 2.3 Ok

1 MSFC3 Daughterboard WS-SUP720 SAL1106G5RS 2.6 Ok

2/0 2xGE SPA SPA-2X1GE JAE11076E0X 2.2 Ok

2/1 2xGE SPA SPA-2X1GE JAE11076E62 2.2 Ok

Mod Online Diag Status

---- -------------------

1 Pass

2 Pass

2/0 Not Applicable

2/1 Not Applicable

However when I do a 'sh int status' only the two gig interfaces on the Sup720 show up:

ROC-RT7604A-CR>sh int status

Port Name Status Vlan Duplex Speed Type

Gi1/1 connected routed full 1000 1000BaseT

Gi1/2 disabled 1 full 1000 No Transceiver

ROC-RT7604A-CR>

Yet one of the SPAs is active as shown here:

ROC-RT7604A-CR>sh int g2/0/0

GigabitEthernet2/0/0 is up, line protocol is up

Hardware is GigEther SPA, address is 0017.0fac.a600 (bia 0017.0fac.a600)

Description: to ACN-7604-CD-A G2/0/0

Internet address is xxx.xxx.xxx.xxx/30

MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation ARPA, loopback not set

Keepalive not supported

Full Duplex, 1000Mbps, link type is auto, media type is LX

output flow-control is unsupported, input flow-control is unsupported

ARP type: ARPA, ARP Timeout 04:00:00

........

1. Is there a reason why the SPA interfaces do not show up when doing a 'sh int status'?

2. Also why does the 'sh mod' show 'not applicable' for the 2/0 & 2/1 diag status fields?

I have this problem too.
0 votes
  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
Anonymous (not verified) Wed, 06/27/2007 - 05:43

The interface may be down due to module problems.And if the interface are used for SPAN then its status will be down.

Newly added interface does not come online in a PortChannel. PortChannel mode is on.

Enable PortChannel manually or change PortChannel mode to active. Or, use the no shutdown CLI command to enable the PortChannel manually or use the channel-mode active CLI command in the interface submode for the PortChannel interface.

Actions

This Discussion