06-20-2007 08:09 AM - edited 03-05-2019 04:51 PM
In my 7604, 12.2(33)SRB1, I have a couple SIP-400s with 2GE-SPAs in them. Here is 'sh mod':
ROC-RT7604A-CR>sh mod
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 2 Supervisor Engine 720 (Active) WS-SUP720-3B SAL1106GKP2
2 0 4-subslot SPA Interface Processor-400 7600-SIP-400 JAE1112A45Z
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
1 0017.9444.68fc to 0017.9444.68ff 5.3 8.4(2) 12.2(33)SRB1 Ok
2 0015.2b89.a1d0 to 0015.2b89.a24f 2.4 12.2(33)SRB1 12.2(33)SRB1 Ok
Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
1 Policy Feature Card 3 WS-F6K-PFC3B SAL1106GLRR 2.3 Ok
1 MSFC3 Daughterboard WS-SUP720 SAL1106G5RS 2.6 Ok
2/0 2xGE SPA SPA-2X1GE JAE11076E0X 2.2 Ok
2/1 2xGE SPA SPA-2X1GE JAE11076E62 2.2 Ok
Mod Online Diag Status
---- -------------------
1 Pass
2 Pass
2/0 Not Applicable
2/1 Not Applicable
However when I do a 'sh int status' only the two gig interfaces on the Sup720 show up:
ROC-RT7604A-CR>sh int status
Port Name Status Vlan Duplex Speed Type
Gi1/1 connected routed full 1000 1000BaseT
Gi1/2 disabled 1 full 1000 No Transceiver
ROC-RT7604A-CR>
Yet one of the SPAs is active as shown here:
ROC-RT7604A-CR>sh int g2/0/0
GigabitEthernet2/0/0 is up, line protocol is up
Hardware is GigEther SPA, address is 0017.0fac.a600 (bia 0017.0fac.a600)
Description: to ACN-7604-CD-A G2/0/0
Internet address is xxx.xxx.xxx.xxx/30
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive not supported
Full Duplex, 1000Mbps, link type is auto, media type is LX
output flow-control is unsupported, input flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
........
1. Is there a reason why the SPA interfaces do not show up when doing a 'sh int status'?
2. Also why does the 'sh mod' show 'not applicable' for the 2/0 & 2/1 diag status fields?
06-27-2007 05:43 AM
The interface may be down due to module problems.And if the interface are used for SPAN then its status will be down.
Newly added interface does not come online in a PortChannel. PortChannel mode is on.
Enable PortChannel manually or change PortChannel mode to active. Or, use the no shutdown CLI command to enable the PortChannel manually or use the channel-mode active CLI command in the interface submode for the PortChannel interface.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: